Authorized Corro-Protec Dealer · DuPage County, IL

Corro-Protec Powered Anode Rods in DuPage County, IL

GSHA crews travel into DuPage County from our Woodstock headquarters and our Lake Bluff office. As an authorized Corro-Protec dealer and installer, we replace the sacrificial anode in gas and electric tank water heaters with a Corro-Protec powered anode rod, with our own plumbing crews doing the work and our own licensed electricians adding an outlet when one is needed.

Much of DuPage drinks Lake Michigan water. The DuPage Water Commission buys treated water from the City of Chicago and delivers it to member communities; its 2025 report lists chlorine as the disinfectant, and Elmhurst’s 2025 report describes the water as about 144 mg/L, or about 8 grains per gallon, of hardness. That is moderate, consistent water, and it still leaves the tank in your basement depending on an anode.

Request a free installation estimateCall (224) 220-3660

LAKE MICHIGANPUMP STATIONWATER HEATER
DuPage Water Commission members receive Lake Michigan water purchased from the City of Chicago.

Communities we serve in DuPage County

Our published service area includes Addison, Bensenville, Bloomingdale, Carol Stream, Elmhurst, Glen Ellyn, Glendale Heights, Itasca, Lombard, Roselle, Villa Park, Warrenville, West Chicago, Wheaton (the county seat), Winfield and Wood Dale. Aurora reaches into DuPage from Kane County, and several other covered municipalities straddle county lines, so the city or village on your water bill matters more than the county.

Burr Ridge is not named on our ZIP-code list, although its 60527 ZIP code is listed; if you live there, please confirm your address with us at (224) 220-3660 or through the estimate form before scheduling. The full list is on our service area page.

What DuPage County water means for a water heater

The DuPage Water Commission’s 2025 report

The DuPage Water Commission’s 2025 consumer confidence report identifies its source as water purchased from the City of Chicago, which draws from Lake Michigan and treats it at its Jardine and Sawyer plants. Chlorine is the disinfectant, at a highest level of 1.50 ppm (range 0.95 to 1.50 ppm) in the Commission’s data. The City of Chicago data in the same report lists sodium at 8.67 to 9.10 ppm and sulfate at 26.8 to 27.2 ppm.

Elmhurst’s 2025 report: a hardness figure

Elmhurst buys its water from the Commission, and its 2025 water quality report adds the number most homeowners want: hardness of about 144 mg/L as calcium carbonate, or about 8 grains per gallon. Elmhurst’s distribution data shows chlorine at 1.0 to 1.3 ppm. The Commission’s own report does not state hardness, so Elmhurst’s is the published figure we cite for Commission water.

ItemPublished figureSource
SourceLake Michigan, purchased from the City of ChicagoDuPage Water Commission 2025 CCR
DisinfectantChlorine, 0.95-1.50 ppm (Commission); 1.0-1.3 ppm (Elmhurst)DWC and Elmhurst 2025 reports
HardnessAbout 144 mg/L, about 8 grains per gallonElmhurst 2025 report
Sulfate26.8-27.2 ppm (City of Chicago data)DuPage Water Commission 2025 CCR

Some DuPage communities and unincorporated areas are served by other systems or private wells; your utility’s annual report is the authority for your address.

Corro-Protec guidance for DuPage County homes

Why bother on good lake water?

Moderately hard, chlorinated lake water is about as predictable as water gets, but a glass-lined steel tank still corrodes wherever its lining is imperfect, and a sacrificial anode is still being used up to prevent that. Corro-Protec’s FAQ notes that water heater manufacturers often require anode inspection every one to three years to keep tank warranties valid, which few homeowners ever arrange. A Corro-Protec rod is designed to protect the tank with a small current from a titanium rod coated with mixed metal oxide, rather than by dissolving, and a green light on its power supply confirms it is working.

Hot-water odor on city water

A rotten-egg smell from the hot taps only can happen on municipal water too. Corro-Protec attributes the smell to hydrogen sulfide produced when sulfur-reducing bacteria react with sulfates, sometimes along with a magnesium anode, and says its rod eliminates it in most cases within 24 hours. The Minnesota Department of Health explains that a magnesium anode can supply electrons that help convert sulfate to hydrogen sulfide, and advises against simply removing the anode because that may significantly shorten the heater’s life. We confirm the source by smelling the hot and cold taps before recommending anything.

Softeners and filters

At about 8 grains per gallon, some DuPage homeowners choose to soften. Corro-Protec says its rod can be used safely with any water treatment system. It does not soften water itself; for that, see our water filtration page.

Choosing the model

The standard 40-89 gallon dedicated-port rod (part 96387) fits the usual 40 or 50 gallon tank with an anode port on top. Heaters with the anode in the hot water outlet, as on many Bradford White models, need the hot-outlet version (96383); Corro-Protec warns that a dedicated-port model installed in a hot water outlet voids the warranty. The 10-39 gallon rod (96386) and the 19-inch 90-120 gallon rod (96388) cover smaller and larger tanks.

Permits, power and installation considerations

How one DuPage city writes the rules

Naperville’s Guide to Building Permits is a useful example of how a DuPage municipality draws the line. It lists new water heaters, including a change in power source, as plumbing work that requires a permit. Among work that does not require a permit, it lists the clearing of stoppages or repairing of leaks in pipes, valves or fixtures; minor electrical repair work; and the connection of approved portable electrical equipment to approved permanently installed receptacles. It also says a homeowner may perform most ordinary repairs without a permit. The guide does not mention anode rods by name. Each DuPage municipality adopts its own rules, so GSHA confirms with the building department for your address and pulls any permit the job requires, for example when we add a new receptacle or replace the heater.

Power

The Corro-Protec power supply has a 12-foot cord, and Corro-Protec’s warranty requires continuous power and proper grounding. If the nearest grounded receptacle is out of reach or on a switched circuit, GSHA’s licensed electricians install a suitable one.

Headroom and tank condition

The regular rod needs about a foot of space above the tank, and the X-Large rod more. Before installing we check for rust at the fittings, a dripping relief valve or a weeping tank. A powered anode protects a sound tank; it cannot fix a leaking one.

Retrofit the anode, or replace the water heater?

A Corro-Protec rod makes the most sense on a tank that is sound and worth keeping. When the heater is near the end of its life, the better money may go toward a new one. These are the factors we weigh with DuPage homeowners.

  • Tank condition. Rust at the fittings, water at the base or a badly corroded old anode point toward replacement. A powered anode cannot reverse corrosion that has already gone through the tank.
  • The smell. If the hot water smells and the tank is otherwise healthy, a retrofit addresses the cause that Corro-Protec and the Minnesota Department of Health describe, without replacing the heater.
  • Type of new heater. If you replace with a tankless heater, there is no anode at all; if you replace with a new storage tank, a Corro-Protec rod can go into the new tank too, since Corro-Protec fits storage heaters of 10 to 120 gallons. Corro-Protec states that a compatible, properly installed rod should not, by itself, void the water heater manufacturer’s warranty.
  • Permits. A new water heater is permit work in places like Naperville, and GSHA handles that permit. An anode retrofit on an existing heater is a smaller job, and we confirm locally whether any permit applies.

Our article on gas tank vs. tankless vs. heat pump water heaters compares replacement options, and our water heater services page covers repair and replacement.

After installation: what DuPage homeowners should know

A Corro-Protec rod is close to maintenance-free, but a few habits keep it working and keep the warranty intact.

  • Check the green light occasionally. Corro-Protec says the LED on the power supply lights only when the system is working properly and goes out if there is a fault. If it is dark, confirm the plug is seated and the receptacle has power, for example that a GFCI outlet has not tripped, then call us if it stays off.
  • Leave it plugged in. The rod protects the tank only while powered, and Corro-Protec’s warranty requires continuous power. Do not unplug it when you travel.
  • Draining is fine. If the tank is drained for service, Corro-Protec says the rod switches itself off automatically when the tank is empty.
  • Keep the paperwork. A warranty claim needs proof of purchase and the serial number. We leave both with you and register the extended warranty within Corro-Protec’s 90-day window.
  • Keep up the rest of the heater. The relief valve, the venting on a gas heater and the connections still need the attention your heater’s manufacturer recommends. Our water heater services cover that.
  • If the smell returns. Corro-Protec says the hot-water smell usually clears within 24 hours of installation. If it comes back, check the light and call us; we will compare the hot and cold taps again.

Corro-Protec models we install in DuPage County

The same residential models are available throughout the county. Specifications are on the main Corro-Protec page.

Dedicated port, 10-39 gal

Compact tanks with a separate anode port.

Part no. 96386

Model details

Dedicated port, 40-89 gal

The standard model for typical 40 and 50 gallon tanks.

Part no. 96387

Model details

Dedicated port, 90-120 gal

X-Large 19-inch rod for big tanks.

Part no. 96388

Model details

Hot water outlet, 10-120 gal

Fits most Bradford White heaters; Buderus version available.

Part no. 96383 (96382 Buderus)

Model details

Corro-Protec offers in DuPage County

Ask GSHA about current Corro-Protec offers.

When this page was checked on 2026-10-23, no Corro-Protec promotion was confirmed current on both corroprotec.com and gshaservices.com, so none is advertised. Corro-Protec’s product page describes a 90-day money-back guarantee with its limited warranty, and GSHA financing is on our financing page.

DuPage County questions and answers

Is DuPage water hard?

Moderately. Elmhurst’s 2025 report puts its Lake Michigan water, bought through the DuPage Water Commission, at about 144 mg/L or about 8 grains per gallon. A powered anode does not change hardness; it protects the tank.

Do I need a permit to replace an anode rod in Wheaton or Lombard?

Municipal rules vary. Naperville’s permit guide, for example, requires a permit for new water heaters but does not name anode rods, and exempts connecting approved equipment to an existing receptacle. GSHA confirms with your building department and pulls any permit the job needs.

My hot water smells but the cold does not. Is a powered anode the fix?

That pattern points to the water heater, and Corro-Protec says its rod eliminates the smell in most cases within 24 hours. We confirm at the visit before installing.

How much electricity does it use?

Corro-Protec estimates that its best-selling rod uses about $2 to $3 of electricity per year.

Can it go into a brand-new water heater?

Yes, if the new heater is a compatible storage tank. Corro-Protec states that a compatible, properly installed rod should not, by itself, void the heater manufacturer’s warranty.

What warranty comes with it?

Corro-Protec’s written warranty covers the rod and power supply for 5 years, and the rod for up to 20 years, prorated from year 6, when registered within 90 days of purchase. GSHA registers it with you.

More Corro-Protec and water heater pages

Corro-Protec Authorized Dealer in Illinois (main page) · Corro-Protec powered anode rod installation · Water heater services · Gas tank vs. tankless vs. heat pump water heaters · Water filtration systems

Other counties

Request a free Corro-Protec installation estimate

Tell us about your water heater in DuPage County: brand, size, fuel, rough age and whether the hot water smells. We will follow up to confirm the right Corro-Protec model and schedule a free, no-obligation visit.

Send the form or call

Use the form here, book online, or call (224) 220-3660.

Fit check

A GSHA technician confirms the anode location, thread, headroom and power, and checks the condition of the heater.

Written quote

You receive an itemized quote for the rod, installation, any electrical work and warranty registration. No obligation.

If the form does not load, email info@gshaservices.com or call (224) 220-3660.

About GSHA Services, LTD

GSHA Services, LTD is a licensed and insured heating, cooling, electrical, plumbing and generator contractor and an authorized Corro-Protec dealer and installer. Offices: 1257 Cobblestone Way, Suite A, Woodstock, IL 60098 and 11 N Skokie Hwy, Lake Bluff, IL 60044. Phone (224) 220-3660. Email info@gshaservices.com. GSHA Services is an independent dealer, not Corro-Protec; product warranties are provided by the manufacturer. See the full service area by ZIP code. Contact us · Financing · All products and brands

Sources

  1. DuPage Water Commission, 2025 CCR Report — https://dpwc.org/wp-content/uploads/2026/03/2025-DuPage-Water-Commission-CCR-Report.pdf (accessed 2026-10-23)
  2. City of Elmhurst, Water Quality Report 2025 — https://cms3.revize.com/revize/elmhurst/Document%20Center/Services/Public%20Works/Utility%20Division/Water%20Quality%20Report%202025%20FINAL%20.pdf (accessed 2026-10-23)
  3. City of Naperville, Guide to Building Permits — https://www.naperville.il.us/contentassets/2beca6c2168344f3a65cc84c9479731b/601-guide-to-building-permits-103122.pdf (accessed 2026-10-23)
  4. Minnesota Department of Health, Hydrogen Sulfide in Well Water — https://www.health.mn.gov/communities/environment/water/wells/waterquality/hydrosulfide.html (accessed 2026-10-23)
  5. Corro-Protec FAQ — https://www.corroprotec.com/faq/ (accessed 2026-10-23)
  6. Corro-Protec Powered Anode Rod for Water Heaters (product page) — https://www.corroprotec.com/product/water-heater-anode-rod/ (accessed 2026-10-23)
  7. Corro-Protec Limited Warranty — https://www.corroprotec.com/corro-protec-limited-warranty/ (accessed 2026-10-23)
  8. GSHA service area page (ZIP-code list) — https://gshaservices.com/about-gsha-services/service-area/ (accessed 2026-10-23)