Authorized Williams dealer · Kane County, IL
Williams Wall Furnaces Installed in Kane County, IL
Kane County homeowners are served from GSHA Services’ headquarters at 1257 Cobblestone Way, Suite A, Woodstock, IL 60098. GSHA has no office in Kane County; our crews drive down from Woodstock to St. Charles, Geneva, Batavia, Elgin, Aurora and the other communities on our service list. As an authorized Williams dealer and installer, GSHA supplies and installs Williams direct-vent wall furnaces, Forsaire counterflow furnaces, Monterey top-vent furnaces, floor furnaces and console heaters, and handles the gas piping, venting, any electrical work by our own licensed electricians, the permit and the inspection.
Kane County counted 516,522 residents in the 2020 Census, and of roughly 184,700 occupied homes about 86 percent heat with utility gas, about 11.5 percent with electricity and about 1.5 percent with propane (U.S. Census Bureau, 2020-2024 American Community Survey). The median home was built in 1985. Put together, that describes a lot of gas-heated houses with a finished basement, an addition, a three-season room or an attached garage that the central system serves poorly, which is the kind of space a Williams wall furnace is built to heat on its own.
Communities we serve in Kane County
GSHA’s service-area ZIP list includes St. Charles, Geneva (the county seat), Batavia, Elgin, Aurora, Carpentersville, East Dundee and West Dundee, Hampshire, Algonquin, Huntley, Bartlett and the unincorporated Wasco area near St. Charles. Several cross county lines: St. Charles and Batavia extend into DuPage County, Elgin into Cook, and Aurora into DuPage, Kendall and Will; Algonquin and Huntley straddle the McHenry line; and Bartlett is mainly a Cook and DuPage village with a small piece in Kane. The building department that covers your street sets the permit rules.
South Elgin, North Aurora, Montgomery, Sugar Grove, Elburn and Gilberts are also on our published ZIP list. Campton Hills, Pingree Grove and Sleepy Hollow are not named on it, although they use listed ZIP codes such as 60175, 60140 and 60118, so please confirm coverage before scheduling. The full list is on our service area page.
Choosing a Williams unit for a Kane County home
The cold room problem. In a house built around the county’s 1985 median, the furnace and ductwork were sized for the original floor plan. A bonus room over the garage, a sunroom or a basement rec room added later often runs several degrees colder. Rather than rebalancing ducts that cannot reach, a Williams direct-vent wall furnace on an exterior wall gives that room its own heat source and thermostat. The gravity direct-vent models come in 14,000, 22,000 and 30,000 BTU/hr input sizes and need no electricity; for a small office or bathroom-sized space, the 7,400 BTU/hr high-efficiency direct-vent unit mounts on the wall with no floor space and has a built-in seven-day programmable timer.
Larger spaces and more than one room. A walkout lower level or an in-law suite may need more than a gravity unit can spread. The Forsaire counterflow furnaces add a one- or two-speed blower (240 to 440 CFM on a 115-volt cord) and are rated up to 80 percent AFUE. Top-vent Forsaire models run from 35,000 to 65,000 BTU/hr and vent through the roof; direct-vent Forsaire models run from 40,000 to 60,000 BTU/hr and vent through a wall up to 12 inches thick. Williams’ optional side- and rear-outlet kits can push heat into up to three rooms, and front diffusing grilles direct it left, right or both.
Garages and shops. Williams markets direct-vent counterflow, gravity and high-efficiency models for garages and workshops, with natural-gas or propane versions and all vent materials included. For a large or tall garage, compare against a unit heater on our garage heater installation page.
Older wall furnaces in the river towns. Where an older home in Elgin, Aurora, Geneva or St. Charles still has an original gravity wall furnace or floor furnace, Williams makes like-for-like units: Monterey top-vent gravity furnaces at 25,000, 35,000 and 50,000 BTU/hr, and floor furnaces at 45,000 and 60,000 BTU/hr. We inspect the existing vent and gas line before deciding whether to reuse them.
Permits, utilities and installation considerations
Kane County municipalities each publish their own rules for furnace work, and several of them spell out exactly the details a wall furnace installation has to get right. GSHA pulls the permit and schedules the inspection.
- St. Charles. The city’s Building Permits FAQs say a permit and final inspection are required when a furnace is replaced. The unincorporated Wasco area permits through Kane County.
- Geneva. The Building Division’s Furnace/Air Conditioner/HVAC Replacement handout requires a permit before a furnace is replaced, listed a $50 fee issued over the counter as published in September 2026, and asks 24 hours’ notice for inspections. Its checklist reads like a wall-furnace punch list: venting and chimney draft, a gas shut-off valve within 6 feet of the appliance with a union and sediment trap, combustion air, and fireblocking, which matters whenever a Monterey or Forsaire is recessed into a stud cavity. The handout notes that the Mill Creek subdivision permits through Kane County.
- Batavia. The Building Permit Applications page lists heating and mechanical equipment among projects needing a permit, filed through the One Stop Permit Portal; the fee schedule priced a replace-only furnace permit at $45 as published in September 2026.
- Elgin. Ordinance G15-25 requires a permit to install or alter any HVAC equipment, issued only to licensed warm-air heating contractors or the owner-occupant, and requires interior gas piping to be schedule 40 black iron from the meter to the appliance connector, with limited exceptions. The city’s Miscellaneous HVAC Quick Guide handles HVAC work as a Quick Permit with a final inspection, and its Permits page makes the permit holder responsible for scheduling inspections.
- Unincorporated Kane County. The Building & Zoning Division permits unincorporated properties, including Mill Creek and Wasco, through its web portal and asks 48 to 72 hours’ notice for inspections.
- Aurora and others. For Aurora and other municipalities not listed, GSHA confirms the permit path for your address before work starts.
Venting and combustion air
Combustion air is where Williams’ direct-vent design pays off: Williams states that its direct-vent furnaces take combustion air from outside and use no room air, so a direct-vent unit in a tight, well-sealed room does not depend on air leaking in from the rest of the house. Top-vent Monterey and Forsaire models draw combustion air from the room and vent through the roof with Williams’ oval vent system, so the inspector will look at combustion air and draft, as Geneva’s checklist spells out. GSHA works out which type fits the room before quoting. Direct-vent wall limits are 24 inches for gravity models and 12 inches for counterflow models, with vent extensions available.
Utilities
Nicor Gas is the gas utility across Kane County; its ICC tariff names the county’s municipalities and the unincorporated territory around them, and its ZIP lookup confirms an address. Nicor’s 2026 residential rebates pay on furnaces only at 95 and 97 percent AFUE, and the Williams models we install are rated at or below 80 percent, so budget a Williams unit without that rebate. On the electric side, Batavia, Geneva and St. Charles run their own city electric utilities while ComEd serves most of the rest of the county; that matters only for the blower-equipped Williams models, which plug into an ordinary 115-volt outlet or a hardwired circuit.
Gas, electrical and what GSHA handles
GSHA runs the gas line in the material your municipality requires (black iron in Elgin), installs the shut-off, union and sediment trap, sets the furnace to Williams’ clearances, installs the vent kit and any fireblocking, and pressure-tests and lights the unit. Our licensed electricians add an outlet or circuit for counterflow models. We pull the permit, attend the inspection and show you how to use the thermostat and relight the pilot.
Williams products we install in Kane County
The same Williams lines are available county-wide. Full models, ratings and spec-sheet details are on the main Williams page.
Direct-Vent Wall Furnaces
Gravity units vented through the wall; no electricity required.
14,000 / 22,000 / 30,000 BTU/hr
DetailsHigh-Efficiency Direct-Vent
Low-profile sealed-combustion wall units for small rooms and garages.
7,400 / 17,700 BTU/hr
DetailsForsaire Counterflow
Blower-equipped, up to 80% AFUE, top-vent or direct-vent.
35,000-65,000 BTU/hr
DetailsMonterey Top-Vent
Recessed or surface-mount gravity furnace vented through the roof.
25,000 / 35,000 / 50,000 BTU/hr
DetailsFloor Furnaces
Blower-free furnace under a floor register; no electricity.
45,000 / 60,000 BTU/hr
DetailsVented Room Heaters
Enclosed or glass-front console heaters; optional blower.
20,000-65,000 BTU/hr
DetailsGarage & Workshop
Direct-vent counterflow, gravity and high-efficiency models for garages.
Natural or propane
Garage heatersSolana Electric
Electric counterflow furnace for spaces without gas.
Freestanding or recessed
DetailsCurrent Williams offers
Ask GSHA about current Williams offers.
Financing programs available through GSHA are on our financing page.
Questions and answers
Do you cover my part of Kane County?
Our ZIP list covers St. Charles, Geneva, Batavia, Elgin, Aurora, Carpentersville, East and West Dundee, Hampshire, Algonquin, Huntley, Bartlett and the Wasco area. For Campton Hills, Pingree Grove or Sleepy Hollow, call (224) 220-3660 to confirm first.
Why does Geneva care about fireblocking for a furnace?
Geneva’s furnace replacement checklist includes fireblocking along with venting, combustion air and the gas shut-off. When a Williams Monterey or Forsaire furnace is recessed into a wall, the stud cavity around and above it is opened, and the code expects it to be closed off properly. GSHA includes that work in the installation.
Does Elgin require a licensed contractor for a wall furnace?
Elgin’s Ordinance G15-25 issues HVAC permits only to licensed warm-air heating contractors or the owner-occupant, and requires schedule 40 black iron gas piping from the meter to the appliance connector, with limited exceptions. GSHA pulls the permit and runs the piping to that standard.
Which Williams model is best for a cold bonus room?
It depends on the room’s size, the wall it can hang on and whether there is power nearby. A direct-vent gravity furnace on an exterior wall is the simplest; a Forsaire direct-vent counterflow adds a blower for larger rooms; and the 7,400 BTU/hr high-efficiency model suits a small office. We measure and recommend at the estimate.
Will Nicor give me a rebate?
Not for a Williams furnace under Nicor’s 2026 furnace rebate, which starts at 95 percent AFUE. Williams units are chosen for zone heating where ductwork does not reach.
Do Williams furnaces need electricity?
Gravity direct-vent, Monterey, floor and console models need none, according to Williams. Forsaire counterflow models and the 17,700 BTU/hr high-efficiency unit need a 115 to 120 volt supply, which our licensed electricians provide.
What warranty does Williams provide?
The Williams spec sheets state a 10-year limited warranty on the combustion chamber and one year on other parts, contingent on installation by a qualified installer.
More Williams and heating pages
Williams authorized dealer in Illinois (main page) · Garage heater installation · Furnace installation · Furnace repair
Other counties
Request a free Williams installation estimate
Tell us about the room or building you want to heat in Kane County. We will schedule a free, no-obligation visit, measure the space, choose the vent route, check the gas line and any electrical needs, and give you a written quote.
Send the form or call
Use the form here, book online, or call (224) 220-3660.
On-site visit
A GSHA comfort advisor measures the space, checks venting, combustion air, gas and power, and explains the Williams options that fit.
Written quote
You receive an itemized quote with the equipment, vent kit, gas piping, any electrical work and the permit. No obligation.
If the form does not load, email info@gshaservices.com or call (224) 220-3660.
About GSHA Services, LTD
GSHA Services, LTD is a licensed and insured heating, cooling, electrical, plumbing and generator contractor and an authorized Williams dealer and installer. Kane County is served from our headquarters at 1257 Cobblestone Way, Suite A, Woodstock, IL 60098. Phone (224) 220-3660. Email info@gshaservices.com. See the full service area by ZIP code. Contact us · Financing · All products and brands
Sources
- Census Reporter API, ACS 2020-2024 5-year tables B25035, B25040, Kane County, IL (05000US17089) — https://api.censusreporter.org/1.0/data/show/acs2024_5yr?table_ids=B25035,B25040&geo_ids=05000US17089 (accessed 2026-09-16)
- Williams Direct-Vent spec sheet L1109 (June 2026) — https://williamscomfort.com/wp-content/uploads/2026/06/L1109_Direct_Vent_specSheet_6_26.pdf (accessed 2026-10-23)
- Williams High-Efficiency Direct-Vent spec sheet L1457 — https://williamscomfort.com/wp-content/uploads/2023/09/L1457_High_Efficiency-DV_spec_sheet-8_25.pdf (accessed 2026-10-23)
- Williams Forsaire spec sheet L1158 (June 2026) — https://williamscomfort.com/wp-content/uploads/2026/06/L1158_Forsaire_spec_sheet_EN_6_26.pdf (accessed 2026-10-23)
- Williams Forsaire Direct Vent Counterflow product page (direct-vent design, outside combustion air) — https://williamscomfort.com/product/forsaire-direct-vent-counterflow-furnaces/ (accessed 2026-10-23)
- Williams Garage Furnaces spec sheet L1171 — https://williamscomfort.com/wp-content/uploads/2023/09/L1171_Garage_spec_sheet_4_21-1.pdf (accessed 2026-10-23)
- Williams Monterey spec sheet L1073 (June 2026) — https://williamscomfort.com/wp-content/uploads/2026/06/L1073_Monterey_spec_sheet_6_26_EN.pdf (accessed 2026-10-23)
- City of St. Charles – Building Permits FAQs — https://www.stcharlesil.gov/Services/Forms-Permits-Applications/Building-Permits/Building-Permits-FAQs (accessed 2026-09-16)
- City of Geneva – Furnace/Air Conditioner/HVAC Replacement handout — https://www.geneva.il.us/DocumentCenter/View/14/Furnace-and-Air-Conditioner (accessed 2026-09-16)
- City of Batavia – Building Permit Applications — https://www.bataviail.gov/o/ed/page/building-permit-applications (accessed 2026-09-16)
- City of Batavia – Building Permit Fee Schedule — https://www.bataviail.gov/o/ed/page/building-permit-fee-schedule (accessed 2026-09-16)
- City of Elgin – Local HVAC Amendments, Ordinance G15-25 — https://elginil.gov/DocumentCenter/View/830/Local-HVAC-Amendments (accessed 2026-09-16)
- City of Elgin – Miscellaneous HVAC Quick Guide — https://elginil.gov/DocumentCenter/View/75851/Misc-HVAC-Quick-Guide- (accessed 2026-09-16)
- City of Elgin – Permits — https://elginil.gov/2614/Permits (accessed 2026-09-16)
- Kane County Building & Zoning Division — https://www.kanecountyil.gov/FDER/Pages/Development/Building%26ZoningDivision.aspx (accessed 2026-09-16)
- Nicor Gas – Our Service Area — https://www.nicorgas.com/company/where-we-are/our-service-area.html (accessed 2026-10-23)
- Nicor Gas Residential Rebates 2026 — https://www.nicorgas.com/ways-to-save/residential-savings/rebates.html (accessed 2026-10-23)
- GSHA service area page (ZIP-code list) — https://gshaservices.com/about-gsha-services/service-area/ (accessed 2026-10-23)
