Authorized Williams dealer · Cook County, IL

Williams Wall Furnaces Installed in Cook County, IL

GSHA Services, LTD is an authorized Williams dealer and installer serving Cook County’s northern, northwestern and near-western suburbs, plus Tinley Park and Lemont. GSHA has no office in Cook County: most Cook County work is dispatched from our Lake Bluff office, and the county’s northwest edge is handled from Woodstock. We supply and install Williams direct-vent wall furnaces, Forsaire counterflow furnaces, Monterey top-vent furnaces, floor furnaces and vented console heaters, with the gas piping, venting, any electrical work by our own licensed electricians, the permit and the inspection.

Cook County has the oldest housing GSHA serves: the median home was built in 1961 and about 28 percent of housing units date from 1939 or earlier, and more than half of all units are in buildings with two or more units (U.S. Census Bureau, ACS 2020-2024). That is the setting where wall furnaces, floor furnaces and console heaters have been heating enclosed porches, attic rooms, garden apartments and coach houses for decades, and where a like-for-like Williams replacement is often the most direct fix when one wears out.

Request a free installation estimateCall (224) 220-3660

A Monterey top-vent gravity furnace recesses into the wall and vents up through the roof; no electricity required.

Communities we serve in Cook County

GSHA’s service-area ZIP list covers Arlington Heights, Palatine, Des Plaines, Park Ridge, Mount Prospect, Prospect Heights, Wheeling, Rolling Meadows, Elk Grove Village, Schaumburg, Hoffman Estates and Streamwood in the northwest suburbs; Glenview, Northbrook, Morton Grove, Golf, Skokie, Wilmette, Kenilworth, Winnetka and Glencoe to the north; Franklin Park, Schiller Park, River Grove, Melrose Park, Hillside, Berkeley, Broadview and Westchester to the near west; and Tinley Park and Lemont to the south. Barrington and Buffalo Grove are partly in Lake County, Bartlett in DuPage and Kane, Hanover Park in DuPage, Lemont in DuPage and Will, and Tinley Park in Will; GSHA pulls the permit from whichever municipality your address belongs to.

Only some City of Chicago ZIP codes are on the list, so Chicago homeowners should confirm their address with GSHA first. The same goes for Cicero, Berwyn, Matteson and Richton Park. The full list is on the GSHA service area page; if your ZIP is missing, call (224) 220-3660.

Choosing a Williams unit for a Cook County home

Replacing an old wall or floor furnace. In a pre-war bungalow, two-flat or coach house, the old heater is often a gravity wall furnace recessed between studs or a floor furnace under a register in the main room. Williams makes current versions of both. Monterey top-vent gravity furnaces come in 25,000, 35,000 and 50,000 BTU/hr input, recessed or surface-mounted; the dual-wall 50,000 model puts 25,000 BTU/hr into each of two adjoining rooms, which suits a center wall between a living and dining room. Williams floor furnaces come in 45,000 and 60,000 BTU/hr and circulate air without a blower. Neither needs electricity. We check whether the existing roof vent or floor opening and the gas line can be reused before quoting.

Enclosed porches, attic rooms and garden units. A sun porch enclosed decades ago, a finished attic or a basement apartment is often the coldest space in an older house. On an exterior wall, a Williams direct-vent gravity furnace (14,000, 22,000 or 30,000 BTU/hr input) vents straight through the wall behind it and uses outside air for combustion, so it does not compete with the house for air. For a larger garden apartment, a Forsaire counterflow furnace (35,000 to 65,000 BTU/hr, up to 80 percent AFUE) adds a blower and outlet kits that can carry heat into up to three rooms.

Two-flats and small buildings. With more than half of Cook County’s housing units in buildings of two or more units, separate heat for each unit is a common request. A Williams wall furnace per unit gives each household its own thermostat and gas appliance. Where a building has no gas to a unit, the Williams Solana electric counterflow furnace or a ductless heat pump is the alternative we price.

Garages. For a detached garage off the alley, Williams markets direct-vent counterflow, gravity and high-efficiency models for garages and workshops. Our garage heater installation page covers unit-heater options too.

Permits, utilities and installation considerations

Permits and inspections

Nearly every Cook County address is inside a municipality that issues its own HVAC permit; the Cook County Department of Building and Zoning covers only unincorporated areas and cannot process permits for Chicago or incorporated suburbs (e-Permits). Fees below are those each municipality published; GSHA confirms the current fee when it applies.

  • Arlington Heights lists Furnace Replacement as an over-the-counter permit applied for through its Civic Access portal; the furnace guide asks for the contractor’s proposal.
  • Palatine requires a permit for replacing or installing a heating unit (when a permit is required); replacements are Express permits filed online, and the village’s 2026 furnace handout lists a $103 fee, a possible five-day plan review, a final inspection and an emergency same-location start if the application is filed within one business day.
  • Des Plaines takes applications through its Customer Self Service portal (Building and Permits); City Code 10-13-3 lists HVAC/Mechanical remove and replace at $75 for one- and two-family homes, two inspections included.
  • Park Ridge requires a permit for heating work and schedules inspections with a normal one-to-two-working-day wait (Permits and Inspections).
  • Unincorporated Cook County uses an HVAC permit application that asks for the old and new equipment’s make, model and AFUE, a justification if capacity changes by more than 15 percent, and a Cook County-registered HVAC contractor (Building and Zoning). If an old 35,000 BTU/hr wall furnace is being replaced with a 50,000, that justification comes from our heat-loss calculation.
  • City of Chicago (confirm your address first) exempts only an in-kind furnace replacement of the same type, size and shape in a residential building up to four stories; anything else needs a permit (Department of Buildings). Swapping a wall furnace for a like Williams unit may qualify; moving it, changing its size or switching from a floor to a wall furnace does not.

Venting in older buildings

Old wall furnaces often vent through a metal vent inside the wall to the roof, and old floor furnaces through a vent under the floor to a chimney or roof. Williams floor furnaces use a 4-inch vent rising at least 1/4 inch per foot, and Monterey and Forsaire top-vent models use Williams’ oval vent system with a starter kit. GSHA inspects the existing vent, and if it is corroded, undersized or shared in a way the new unit cannot use, we replace it or choose a direct-vent model that goes out through an exterior wall instead (Williams allows walls up to 24 inches thick for gravity direct-vent models, which covers most double-wythe brick walls; we confirm on site).

Utilities

Nicor Gas serves most of the Cook suburbs on GSHA’s list, Peoples Gas serves Chicago, and North Shore Gas serves communities from Winnetka north; Nicor’s Cook list also names Winnetka, Wilmette and Kenilworth and omits Glencoe, so along the north shore we confirm the gas utility from your bill. ComEd is the electric utility everywhere except Winnetka, which has a municipal electric department. Nicor Gas, Peoples Gas and North Shore Gas all tier 2026 furnace rebates at 95 and 97 percent AFUE, and Peoples Gas and North Shore Gas also require sealed combustion; the Williams models we install are rated at or below 80 percent AFUE, so a Williams installation is budgeted without a gas-utility furnace rebate.

Gas, electrical and what GSHA handles

GSHA runs or extends the gas piping with a shut-off at the appliance, sets the furnace to Williams’ clearances, installs or replaces the vent, and lights and tests the unit. Our own licensed electricians add an outlet or circuit where a Forsaire counterflow or a 17,700 BTU/hr high-efficiency unit needs one. The estimate covers sizing, equipment, permit and inspection, start-up and a walkthrough; financing is on GSHA’s financing page.

Williams products we install in Cook County

The same Williams lines are available county-wide. Full models, ratings and spec-sheet details are on the main Williams page.

Monterey Top-Vent

Recessed or surface-mount gravity furnace vented through the roof.

25,000 / 35,000 / 50,000 BTU/hr

Details

Floor Furnaces

Blower-free furnace under a floor register; no electricity.

45,000 / 60,000 BTU/hr

Details

Direct-Vent Wall Furnaces

Gravity units vented through the wall; no electricity required.

14,000 / 22,000 / 30,000 BTU/hr

Details

Forsaire Counterflow

Blower-equipped, up to 80% AFUE, top-vent or direct-vent.

35,000-65,000 BTU/hr

Details

High-Efficiency Direct-Vent

Low-profile sealed-combustion wall units for small rooms.

7,400 / 17,700 BTU/hr

Details

Vented Room Heaters

Enclosed or glass-front console heaters; optional blower.

20,000-65,000 BTU/hr

Details

Garage & Workshop

Direct-vent counterflow, gravity and high-efficiency models for garages.

Natural or propane

Garage heaters

Solana Electric

Electric counterflow furnace for spaces without gas.

Freestanding or recessed

Details

Current Williams offers

Ask GSHA about current Williams offers.

Financing programs available through GSHA are on our financing page.

Questions and answers

Do you work in Chicago?

Only some City of Chicago ZIP codes are on GSHA’s published list, so city addresses are confirmed one at a time. Call (224) 220-3660 with your address. In the suburbs on our list, we schedule directly.

Does swapping my old wall furnace for a Williams need a permit in Chicago?

The Chicago Department of Buildings exempts only an in-kind furnace replacement of the same type, size and shape in a residential building up to four stories. A same-size wall furnace in the same opening may qualify; a change of size, location or type needs a permit. GSHA confirms before work starts.

Can a Williams dual-wall furnace heat two rooms?

Yes. The Monterey dual-wall model installs in a wall between two rooms and puts 25,000 BTU/hr into each side, according to Williams. It is a gravity unit with no electricity required.

Can you reuse the vent from my old wall furnace?

Sometimes. We inspect it for size, condition and route. If it is not suitable for the new Williams unit, we replace it or recommend a direct-vent model through an exterior wall.

Will Peoples Gas, North Shore Gas or Nicor give me a rebate?

Their 2026 furnace rebates start at 95 percent AFUE, and Peoples Gas and North Shore Gas also require sealed combustion. Williams wall and floor furnaces are rated at or below 80 percent AFUE, so they generally do not qualify.

What does unincorporated Cook County ask for on the permit?

Its HVAC application asks for the old and new equipment’s make, model and AFUE, a justification if heating capacity changes by more than 15 percent, and a Cook County-registered HVAC contractor. GSHA completes it with the Williams specifications and our heat-loss calculation.

What warranty does Williams provide?

Williams states a 10-year limited warranty on the combustion chamber and one year on other parts, contingent on installation by a qualified installer.

More Williams and heating pages

Williams authorized dealer in Illinois (main page) · Garage heater installation · Furnace installation · Furnace repair

Other counties

Request a free Williams installation estimate

Tell us about the heater you have now and the space you want to heat in Cook County. We will schedule a free, no-obligation visit, inspect the existing vent and gas line, check any electrical needs, and give you a written quote.

Send the form or call

Use the form here, book online, or call (224) 220-3660.

On-site visit

A GSHA comfort advisor measures the space, checks the vent, gas and power, and explains the Williams options that fit.

Written quote

You receive an itemized quote with the equipment, vent work, gas piping, any electrical work and the permit. No obligation.

If the form does not load, email info@gshaservices.com or call (224) 220-3660.

About GSHA Services, LTD

GSHA Services, LTD is a licensed and insured heating, cooling, electrical, plumbing and generator contractor and an authorized Williams dealer and installer. Offices in Lake Bluff, IL and at 1257 Cobblestone Way, Suite A, Woodstock, IL 60098. Phone (224) 220-3660. Email info@gshaservices.com. See the full service area by ZIP code. Contact us · Financing · All products and brands

Sources

  1. Census Reporter API, ACS 2020-2024 5-year tables B25024, B25034, B25035, B25040, Cook County, IL (05000US17031) — https://api.censusreporter.org/1.0/data/show/acs2024_5yr?table_ids=B25024,B25034,B25035,B25040&geo_ids=05000US17031 (accessed 2026-09-16)
  2. Williams Monterey spec sheet L1073 (June 2026; dual-wall model) — https://williamscomfort.com/wp-content/uploads/2026/06/L1073_Monterey_spec_sheet_6_26_EN.pdf (accessed 2026-10-23)
  3. Williams Floor Furnace spec sheet L1026 — https://williamscomfort.com/wp-content/uploads/2023/09/L1026_Floor_Furnaces_specSheet_4-21.pdf (accessed 2026-10-23)
  4. Williams Direct-Vent spec sheet L1109 (June 2026) — https://williamscomfort.com/wp-content/uploads/2026/06/L1109_Direct_Vent_specSheet_6_26.pdf (accessed 2026-10-23)
  5. Williams Forsaire spec sheet L1158 (June 2026) — https://williamscomfort.com/wp-content/uploads/2026/06/L1158_Forsaire_spec_sheet_EN_6_26.pdf (accessed 2026-10-23)
  6. Williams Solana Electric Counterflow Furnace — https://williamscomfort.com/product/solana-electric-counterflow-furnace/ (accessed 2026-10-23)
  7. Cook County e-Permits — https://www.cookcountyil.gov/service/e-permits (accessed 2026-09-16)
  8. Cook County HVAC Permit Application (2022) — https://www.cookcountyil.gov/sites/g/files/ywwepo161/files/documents/2022-03/HVAC%20Permit%20Application%202022.pdf (accessed 2026-09-16)
  9. Cook County Building and Zoning — https://www.cookcountyil.gov/agency/building-and-zoning-0 (accessed 2026-09-16)
  10. Village of Arlington Heights – Over-the-Counter Permits — https://www.vah.com/over_the_counter_permits/index.php (accessed 2026-09-16)
  11. Village of Arlington Heights – Furnace Replacement guide — https://www.vah.com/HVAC%20-%20Furnace%20-%20Replacement.pdf (accessed 2026-09-16)
  12. Village of Palatine – When a Building Permit is Required — https://www.palatine.il.us/621/When-a-Building-Permit-is-Required (accessed 2026-09-16)
  13. Village of Palatine – Express Building Permits — https://www.palatine.il.us/609/Express-Building-Permits (accessed 2026-09-16)
  14. Village of Palatine – Furnace Replacement handout (2026) — https://www.palatine.il.us/DocumentCenter/View/2515/Furnace-Replacement-PDF (accessed 2026-09-16)
  15. City of Des Plaines – Building and Permits — https://www.desplainesil.gov/Departments/Community-and-Economic-Development/Building-and-Permits (accessed 2026-09-16)
  16. City of Des Plaines City Code 10-13-3 — https://codelibrary.amlegal.com/codes/desplainesil/latest/desplaines_il/0-0-0-6936 (accessed 2026-09-16)
  17. City of Park Ridge – Permits and Inspections — https://www.parkridge.us/your_government/city_departments/permits_and_inspections_2.php (accessed 2026-09-16)
  18. City of Chicago Department of Buildings – mechanical work not requiring a permit — https://www.chicago.gov/city/en/sites/guide-to-building-permits/home/help/faq/DOB/bldg-permit-not-required/worktype/mechanical.html (accessed 2026-09-16)
  19. Nicor Gas Residential Rebates 2026 — https://www.nicorgas.com/ways-to-save/residential-savings/rebates.html (accessed 2026-10-23)
  20. Peoples Gas residential rebates — https://www.peoplesgasdelivery.com/savings/rebates-residential (accessed 2026-10-23)
  21. North Shore Gas residential rebates — https://www.northshoregasdelivery.com/savings/rebates-residential (accessed 2026-10-23)
  22. GSHA service area page (ZIP-code list) — https://gshaservices.com/about-gsha-services/service-area/ (accessed 2026-10-23)