Authorized Williams dealer · Lake County, IL

Williams Wall Furnaces Installed in Lake County, IL

Lake County homeowners are served from GSHA’s office in Lake Bluff, inside the county, with our Woodstock headquarters as backup. GSHA Services, LTD is an authorized Williams dealer and installer, and we put in Williams direct-vent wall furnaces, Forsaire counterflow furnaces, Monterey top-vent furnaces, floor furnaces and vented console heaters for rooms and buildings that a central furnace does not reach well.

Two local facts shape how a Williams installation goes here. Lake County has two gas utilities, North Shore Gas and Nicor Gas, and which one serves your address decides whose rules and programs apply. And the county’s median home was built in 1983, so many houses already have a sunroom, finished lower level, in-law suite or garage space that was added after the furnace and ductwork were laid out. A wall furnace on an exterior wall heats that space on its own thermostat, with a vent that goes straight out through the wall behind it.

Request a free installation estimateCall (224) 220-3660

A direct-vent wall furnace takes in outside air and vents through the wall it hangs on.

Communities we serve in Lake County

Our published ZIP-code list covers Antioch, Deerfield, Grayslake, Gurnee, Highland Park, Ingleside, Lake Bluff, Lake Forest, Lake Villa, Lake Zurich, Libertyville, Lincolnshire, Mundelein, Round Lake, Vernon Hills, Wadsworth, Wauconda, Waukegan and Zion. Barrington and Buffalo Grove extend into Cook County, and Fox Lake and Island Lake extend into McHenry County; they are on the list too. Ingleside is unincorporated, so its permits run through Lake County rather than a village hall.

Winthrop Harbor, Beach Park, Kildeer, Deer Park, Long Grove and Hawthorn Woods are not named on the published list, though several share listed ZIP codes. If you live there or anywhere else in the county not named above, please confirm coverage when you call (224) 220-3660. The full list is on the GSHA service area page.

Choosing a Williams unit for a Lake County home

Gas is the norm, electricity is the exception. In the Census Bureau’s 2020-2024 American Community Survey, about 83 percent of Lake County’s occupied homes heat with utility gas, about 15 percent with electricity and about 1 percent with propane. Every Williams gas model connects with a 1/2-inch gas line, so in a gas home the question is mostly where the gas piping can reach. In the 15 percent of homes heated electrically, often condos, townhomes and some lakeside or older houses, a gas wall furnace needs a gas supply first; where there is none, the Williams Solana electric counterflow furnace or a ductless heat pump is the comparison we price.

Rooms the ducts never reached. A Williams direct-vent gravity furnace (14,000, 22,000 or 30,000 BTU/hr input) mounted on an exterior wall is the simplest way to warm a three-season porch converted to year-round use, a lower-level family room or a garage apartment. It needs no electricity, so it also keeps one room warm in an outage. For a larger space or a room that should push heat across to another, a Forsaire counterflow furnace adds a blower that moves 240 to 440 CFM from ceiling to floor, and Williams’ optional outlet kits can carry heat into up to three rooms.

Older wall and floor furnaces. Some older Lake County homes, cottages and coach houses still run on an original wall or floor furnace. Williams makes like-for-like replacements in both formats: Monterey top-vent gravity furnaces at 25,000, 35,000 and 50,000 BTU/hr (the 50,000 dual-wall version heats two adjoining rooms), and floor furnaces at 45,000 and 60,000 BTU/hr that circulate air without a blower. We check whether the existing roof vent or floor opening can be reused before quoting.

Garages and workshops. Williams markets direct-vent counterflow, gravity and high-efficiency direct-vent models for garages and workshops, and the 7,400 BTU/hr high-efficiency unit is small enough for a one-car garage or a hobby room. For bigger garages, our garage heater installation page covers unit heaters, and we will compare the two on site.

Permits, utilities and installation considerations

Permits and inspections

A gas wall furnace is a fuel-burning appliance under the mechanical and fuel gas codes, so installing or replacing one is permitted work. Your municipality, or the county for unincorporated addresses, issues the permit; GSHA prepares the application and attends the inspection.

  • Unincorporated Lake County (including Ingleside). Lake County Planning, Building and Development requires a building permit to install or alter any equipment regulated by the building, electrical or mechanical code (Building Permits). Its list of registrations instead of a permit covers like-for-like air conditioner swaps, not furnaces, so a Williams furnace is a permit item.
  • Village of Lake Bluff. The Building Division requires permits for all projects that alter or improve a property and requires every contractor working in the village to hold a village contractor’s license (Building Permit Process). The village enforces the 2018 International Mechanical and Fuel Gas Codes (Adopted Building Codes).
  • Village of Libertyville. For a furnace replacement, the Residential Permits page asks for the contractor’s proposal and a plat of survey showing the vent location, and states that high-efficiency furnaces shall vent to the rear yard or through the roof. That rule matters for a sidewall direct-vent unit, so we confirm with the village how it applies to the Williams model and wall you choose before filing; a top-vent Monterey or Forsaire avoids the question by venting through the roof.
  • Village of Grayslake. The Building Department says almost all building or property changes need a permit and names HVAC as an example (Building FAQs). In Prairie Crossing, the village issues the permit while Lake County performs the plan review and inspections, and the village’s construction handout limits work hours to 7:00 a.m.-7:00 p.m. weekdays and 8:30 a.m.-5:00 p.m. Saturdays.
  • Village of Mundelein. The Building Department takes permits through its online portal and requires 48 hours’ notice for inspections (Building & Construction Permits; Homeowner Project Guide).

Other villages and cities have their own building departments; GSHA confirms the requirements for your address before scheduling.

Venting on Lake County houses

Because a direct-vent Williams furnace vents through the wall directly behind it, picking the wall is picking the vent location. Williams limits wall thickness to 24 inches for gravity direct-vent models and 12 inches for counterflow direct-vent models, includes all vent materials, and offers vent extensions for thicker walls, a vent shield deflector and a vent cap guard where people walk past. On brick or stone veneer we plan the core hole and flashing at the estimate. The cap location follows the Williams installation manual and the fuel gas code the municipality has adopted, and where a village wants vents kept off a side yard facing the neighbors, as Libertyville’s rule does for high-efficiency furnaces, a rear wall or a top-vent model is the fallback.

Utilities

North Shore Gas serves the eastern and central county; its ICC tariff lists Deerfield, Highland Park, Lake Bluff, Lake Forest, Libertyville, Vernon Hills and Zion, among others. Nicor Gas serves the western and northwestern county, including Barrington, Fox Lake, Ingleside, Lake Zurich, Round Lake and Wauconda. Antioch, Grayslake, Gurnee, Lake Villa, Mundelein and Waukegan appear on both companies’ lists, so check your gas bill or Nicor’s ZIP lookup tool. ComEd delivers electricity everywhere in the county. Both gas utilities tier their 2026 furnace rebates at 95 and 97 percent AFUE (North Shore Gas, Nicor Gas), above the ratings of the Williams models we install, so a Williams wall furnace is chosen for zone heating without ducts rather than for a rebate. If a new gas line is needed, the utility answers questions about meter capacity; GSHA handles the piping on your side of the meter.

Gas, electrical and what GSHA handles

GSHA runs the gas line, installs the shut-off, mounts the furnace to Williams’ clearances, installs the vent kit, and pressure-tests and lights the unit. Where a Forsaire counterflow or the 17,700 BTU/hr high-efficiency model needs a 115 to 120 volt supply, our own licensed electricians add the outlet or circuit. We pull the permit, meet the inspector and walk you through the thermostat and pilot relighting.

Williams products we install in Lake County

The same Williams lines are available county-wide. Full models, ratings and spec-sheet details are on the main Williams page.

Direct-Vent Wall Furnaces

Gravity units vented through the wall; no electricity required.

14,000 / 22,000 / 30,000 BTU/hr

Details

High-Efficiency Direct-Vent

Low-profile sealed-combustion wall units for small rooms and garages.

7,400 / 17,700 BTU/hr

Details

Forsaire Counterflow

Blower-equipped, up to 80% AFUE, top-vent or direct-vent.

35,000-65,000 BTU/hr

Details

Monterey Top-Vent

Recessed or surface-mount gravity furnace vented through the roof.

25,000 / 35,000 / 50,000 BTU/hr

Details

Floor Furnaces

Blower-free furnace under a floor register; no electricity.

45,000 / 60,000 BTU/hr

Details

Vented Room Heaters

Enclosed or glass-front console heaters; optional blower.

20,000-65,000 BTU/hr

Details

Garage & Workshop

Direct-vent counterflow, gravity and high-efficiency models for garages.

Natural or propane

Garage heaters

Solana Electric

Electric counterflow furnace for spaces without gas.

Freestanding or recessed

Details

Current Williams offers

Ask GSHA about current Williams offers.

Financing programs available through GSHA are on our financing page.

Questions and answers

Is my Lake County address in GSHA’s service area?

If you are in Antioch, Barrington, Buffalo Grove, Deerfield, Fox Lake, Grayslake, Gurnee, Highland Park, Ingleside, Island Lake, Lake Bluff, Lake Forest, Lake Villa, Lake Zurich, Libertyville, Lincolnshire, Mundelein, Round Lake, Vernon Hills, Wadsworth, Wauconda, Waukegan or Zion, yes. Elsewhere in the county, call (224) 220-3660 to confirm.

Can I vent a Williams furnace out the side of my house in Libertyville?

Libertyville’s residential permit page says high-efficiency furnaces shall vent to the rear yard or through the roof and asks for a plat showing the vent location. We confirm with the village how that applies to the specific Williams model before filing; a rear-wall location or a top-vent model keeps the vent where the village wants it.

Which gas company will I deal with?

North Shore Gas in much of the eastern and central county, Nicor Gas in the west and northwest, and either one in towns such as Antioch, Grayslake, Gurnee, Lake Villa, Mundelein and Waukegan. Your gas bill settles it. GSHA works with either.

Does a Williams wall furnace qualify for a North Shore Gas or Nicor rebate?

Generally no. Both utilities’ 2026 furnace rebates start at 95 percent AFUE, and the Williams furnaces we install are rated at or below 80 percent AFUE. Check each utility’s current rules for any other program.

Will a Williams furnace work during a power outage?

The direct-vent gravity furnaces, the 7,400 BTU/hr high-efficiency model, Monterey top-vent furnaces, floor furnaces and vented room heaters need no electricity, according to Williams. Counterflow models and the 17,700 BTU/hr high-efficiency model use a blower and need power.

Do I need a Lake Bluff contractor’s license holder for the job?

Lake Bluff requires every contractor working in the village to hold a village contractor’s license, and the permit application has an HVAC contractor line. GSHA’s Lake County office is in Lake Bluff and handles that paperwork with the permit.

What comes with a Williams installation from GSHA?

Sizing, the furnace, the Williams vent kit, gas piping and shut-off, any outlet or circuit by our own licensed electricians, the permit and inspection, start-up and a walkthrough. Williams states a 10-year limited warranty on the combustion chamber and one year on other parts when a qualified installer does the work.

More Williams and heating pages

Williams authorized dealer in Illinois (main page) · Garage heater installation · Furnace installation · Furnace repair

Other counties

Request a free Williams installation estimate

Tell us about the room or building you want to heat in Lake County. We will schedule a free, no-obligation visit, measure the space, choose the vent wall or roof path, check the gas line and any electrical needs, and give you a written quote.

Send the form or call

Use the form here, book online, or call (224) 220-3660.

On-site visit

A GSHA comfort advisor measures the space, checks venting, gas and power, and explains the Williams options that fit.

Written quote

You receive an itemized quote with the equipment, vent kit, gas piping, any electrical work and the permit. No obligation.

If the form does not load, email info@gshaservices.com or call (224) 220-3660.

About GSHA Services, LTD

GSHA Services, LTD is a licensed and insured heating, cooling, electrical, plumbing and generator contractor and an authorized Williams dealer and installer. Offices in Lake Bluff, IL and at 1257 Cobblestone Way, Suite A, Woodstock, IL 60098. Phone (224) 220-3660. Email info@gshaservices.com. See the full service area by ZIP code. Contact us · Financing · All products and brands

Sources

  1. Census Reporter API, ACS 2020-2024 5-year tables B25035, B25040, Lake County, IL (05000US17097) — https://api.censusreporter.org/1.0/data/show/acs2024_5yr?table_ids=B25035,B25040&geo_ids=05000US17097 (accessed 2026-09-16)
  2. Williams Direct-Vent spec sheet L1109 (June 2026) — https://williamscomfort.com/wp-content/uploads/2026/06/L1109_Direct_Vent_specSheet_6_26.pdf (accessed 2026-10-23)
  3. Williams Garage Furnaces spec sheet L1171 (wall thickness, vent accessories) — https://williamscomfort.com/wp-content/uploads/2023/09/L1171_Garage_spec_sheet_4_21-1.pdf (accessed 2026-10-23)
  4. Williams Forsaire spec sheet L1158 (June 2026) — https://williamscomfort.com/wp-content/uploads/2026/06/L1158_Forsaire_spec_sheet_EN_6_26.pdf (accessed 2026-10-23)
  5. Williams Monterey spec sheet L1073 (June 2026) — https://williamscomfort.com/wp-content/uploads/2026/06/L1073_Monterey_spec_sheet_6_26_EN.pdf (accessed 2026-10-23)
  6. Williams Floor Furnace spec sheet L1026 — https://williamscomfort.com/wp-content/uploads/2023/09/L1026_Floor_Furnaces_specSheet_4-21.pdf (accessed 2026-10-23)
  7. Williams Solana Electric Counterflow Furnace — https://williamscomfort.com/product/solana-electric-counterflow-furnace/ (accessed 2026-10-23)
  8. Lake County, IL – Building Permits — https://www.lakecountyil.gov/740/Building-Permits (accessed 2026-09-16)
  9. Lake County, IL – Registrations Instead of a Permit — https://www.lakecountyil.gov/762/Registrations-Instead-of-a-Permit (accessed 2026-09-16)
  10. Village of Lake Bluff – Building Permit Process — https://www.lakebluff.org/departments-services/community-development/50-building-permit-process (accessed 2026-09-16)
  11. Village of Lake Bluff – Adopted Building Codes — https://www.lakebluff.org/departments-services/community-development/1003-adopted-building-codes (accessed 2026-09-16)
  12. Village of Libertyville – Residential Permits — https://www.libertyville.com/departments/community_development/building/general_permit/residential_permit.php (accessed 2026-09-16)
  13. Village of Grayslake – Building FAQs — https://www.villageofgrayslake.com/669/Frequently-Asked-Questions-FAQs (accessed 2026-09-16)
  14. Village of Grayslake – General Construction Information Handout — https://villageofgrayslake.com/DocumentCenter/View/10574/BDH-1-General-Construction-Information-Handout (accessed 2026-09-16)
  15. Village of Mundelein – Building & Construction Permits — https://www.mundelein.org/405/Building-Construction-Permits (accessed 2026-09-16)
  16. Village of Mundelein – Homeowner Project Guide — https://www.mundelein.org/DocumentCenter/View/4301/Project-Information-Packet—050426-PDF (accessed 2026-09-16)
  17. Nicor Gas – Our Service Area — https://www.nicorgas.com/company/where-we-are/our-service-area.html (accessed 2026-10-23)
  18. Nicor Gas Residential Rebates 2026 — https://www.nicorgas.com/ways-to-save/residential-savings/rebates.html (accessed 2026-10-23)
  19. North Shore Gas residential rebates — https://www.northshoregasdelivery.com/savings/rebates-residential (accessed 2026-10-23)
  20. GSHA service area page (ZIP-code list) — https://gshaservices.com/about-gsha-services/service-area/ (accessed 2026-10-23)