Authorized Cummins Dealer · Will County, IL

Cummins Generator Dealer Serving Will County, IL

Will County, the fourth most populous county in Illinois with 696,355 residents in the 2020 Census across 849 square miles, is served from the GSHA Services office at 11 N Skokie Hwy, Lake Bluff, IL 60044. Lake Bluff is the nearer of our two offices for every community on this page. Straight-line distances run from about 42 miles for the closest towns to about 56 for the farthest; five of the eleven towns listed below are inside our standard 50-mile radius, and the rest are quoted case by case rather than turned away.

GSHA is an authorized Cummins dealer and installer with its own licensed electricians and gas-line technicians, so one company handles the pad, the gas piping, the transfer switch wiring, the permit and the start-up. Will County’s building ordinance is unusually specific about two things that shape a Cummins installation here: it requires a sump pump for any below-grade space, which puts that pump on every load list, and it sets wiring and contractor rules for unincorporated properties that go beyond what many neighboring counties require.

Request a free installation estimateCall (224) 220-3660

Cummins home standby generator in a weather-resistant enclosure beside a house

Communities we serve in Will County

The table lists eleven of the largest municipalities wholly or mainly in Will County, with 2020 Census populations for the whole municipality, including any part in a neighboring county, and straight-line miles from our Lake Bluff office. Towns past 50 miles are outside our standard radius and quoted case by case; call with your address and we will tell you what applies to your street.

City or villagePopulation (2020 Census)Miles from Lake Bluff (straight-line)Service note
Bolingbrook73,92241.7Inside standard radius; also partly in DuPage County
Romeoville39,86345.4Inside standard radius
Homer Glen24,54347.1Inside standard radius; also partly in Cook County
Plainfield44,76248.8Inside standard radius; also partly in Kendall County
Lockport26,09448.8Inside standard radius
Crest Hill20,45951.8Quoted case by case
Mokena19,88752.1Quoted case by case
New Lenox27,21453.3Quoted case by case
Joliet150,36253.5Quoted case by case; also partly in Kendall County
Frankfort20,29654.1Quoted case by case; also partly in Cook County
Shorewood18,18655.5Quoted case by case

The full ZIP-code list is on our service area page.

Cummins generator guidance for Will County homes

A sump pump on every load list

Will County’s building ordinance (sec. 150.070) requires drain tile around any foundation that encloses below-grade space, connected to a sump pump that discharges to an approved drainage facility or at least ten feet from the house, and forbids tying footing drains or sump pumps to a sanitary sewer or septic system. A home built to that standard depends on its sump pump, and an electric pump does nothing during an outage unless it has backup power. The county’s 1998 Comprehensive Stormwater Management Plan adds that in many parts of the county local drainage flooding is a bigger problem than river flooding, and that there is considerably more flood-prone area than the federal flood maps show. So the sump pump is the first circuit on every Will County generator we size. The Cummins QuietConnect™ 13 kW, rated 54.2 A on natural gas or propane, carries a sump pump, furnace, refrigerator and lights in most homes; add a well pump where there is one. A central air conditioner moves most houses to the 17 kW (70.8 A), and newer, larger homes in Plainfield, Mokena, Frankfort and Homer Glen with two air conditioners usually land on the 20 kW (75 A on natural gas, 83.3 A on propane) using Cummins’ built-in load management for up to four loads.

Wells and septic outside the service areas

The Will County Health Department’s Environmental Health Division permits and inspects private wells and septic systems; in fiscal 2018 it logged 138 septic permits. The county’s land resources plan steers new development toward municipalities and existing sewer and water service areas while preserving farmland, so rural properties in the south and east of the county are more likely to be on a well. A well pump is a motor load with a starting surge and has to be counted in sizing, and a septic field has to be located before we choose the generator pad or trench the gas line.

Nicor gas and the load check

Nicor Gas lists Will County among the counties it serves. Cummins lists full-load natural gas consumption of 217,227 BTU/hr for the 13 kW, 245,954 BTU/hr for the 17 kW and 255,947 BTU/hr for the 20 kW, plus a minimum supply pressure of 3.5 inches of water column at the generator. Our gas technicians check whether your Nicor meter and service line can carry that on top of your furnace, water heater and other gas appliances; when they cannot, we arrange the meter upgrade with Nicor before the installation date. Outside Nicor’s lines, every air-cooled QuietConnect™ runs on propane, and the 20 kW is rated slightly higher on LP.

Cold-weather rating

Cummins says standard air-cooled models perform down to 0°F out of the box and the extreme-cold E models down to -40°F. We quote the E versions (RS13AE, RS17AE, RS20AE) or a Cummins cold weather kit for Will County installations, especially on open rural lots.

Permits, utilities and installation considerations

Who issues the permit

The Will County Building Ordinance (sec. 150.003) applies to buildings and equipment located outside the limits of the county’s cities, villages and incorporated towns. A property inside a municipality gets its generator permit from that city or village. An unincorporated property is permitted by the Will County Land Use Department, Development Services Division, Building Section, 58 East Clinton Street, Suite 100, Joliet (815-727-8634), through the county’s SmartGov Public Portal, where contractors apply, submit documents, schedule inspections and pay fees. The county has adopted the 2018 International Residential Code, the 2017 National Electrical Code, the 2018 International Fuel Gas Code and the 2018 International Mechanical Code, with amendments in the 2021 Will County Building Ordinance.

Wiring and contractor rules for unincorporated Will County

The ordinance does not name standby generators, but sec. 150.003 requires a permit in advance for any electrical installation outside municipal limits and sec. 150.110 requires a permit for all electrical work, so a generator and its transfer switch fall under those rules, and the gas piping falls under the adopted Fuel Gas Code. Sec. 150.110 also requires copper wiring on the load side of the meter and EMT conduit throughout structures, which affects how our electricians run the conductors between the transfer switch, the panel and the generator. The county issues electrical permits only when a licensed and bonded electrical contractor is listed on the application. Since 1993, every contractor working in unincorporated Will County has had to register with the Land Use Department, carry insurance and post a $10,000 surety bond, and electrical contractors and plumbers also file a Letter of Intent for the property. We confirm the submittal list with the Building Section for each job.

Placement

Cummins’ specification sheet says NFPA 37 permits its air-cooled QuietConnect™ units to be installed 18 inches from a building, and the enclosure is 34.1 by 36.0 by 27.3 inches. Local codes still apply, and we confirm placement with the permitting authority during the estimate. Because the county requires sump discharge at least ten feet from the house, we also keep the generator pad out of the discharge path and off low spots where yard water collects. Cummins rates the units at 65 dB(A) at 23 feet under normal load, and the crank-only exercise mode keeps the weekly self-test quieter in subdivisions with close side yards.

Electric service and recent outages

Electric service in Will County comes from ComEd; village resident guides in New Lenox and Homer Glen list ComEd as the electricity provider and Nicor as the gas provider. The Cummins automatic transfer switch isolates the house from ComEd’s line during an outage so the generator never feeds back toward utility crews, then returns the home to utility power when service is restored. The county has recent outage experience: on August 13, 2026, it announced recovery resources after a series of storms, including the severe weather of August 11, damaged property and cut power in several communities, and its emergency management director described the damage and outages as significant.

What GSHA handles

GSHA counts the loads and sizes the generator, checks the Nicor meter or propane supply, installs the transfer switch and wiring to the county’s or municipality’s rules, sets the pad, runs the gas line, pulls the electrical and gas permits, schedules and attends the inspections, starts the generator, tests a transfer under load and registers the warranty.

Cummins products we install in Will County

The same Cummins line is available county-wide. Full specifications are on the main Cummins page.

Cummins QuietConnect Series home standby generator

QuietConnect™ 13 kW

54.2 A on natural gas or propane. Sump pump, well pump, furnace, refrigerator and lights.

Models: RS13A, RS13AE

Explore the Cummins 13 kW
Cummins QuietConnect Series home standby generator

QuietConnect™ 17 kW

70.8 A on either fuel. Essentials plus one central air conditioner.

Models: RS17A, RS17AE

Explore the Cummins 17 kW
Cummins QuietConnect Series home standby generator

QuietConnect™ 20 kW

75 A on natural gas, 83.3 A on propane, with load management for up to four loads.

Models: RS20A, RS20AC, RS20AE, RS20ACE

Explore the Cummins 20 kW

Service & Fault Codes

Maintenance and repair for Cummins home standby generators, including units we did not install.

All Cummins home standby models

Cummins fault codes

Current Cummins offers

Ask GSHA about current Cummins offers.

Promotions change through the year and each names its qualifying equipment and dates, so tell us your planned installation date and we will say which offer, if any, applies. Financing through Synchrony and Service Finance is on our financing page. See financing options.

Questions and answers

Which Will County towns are inside your standard radius?

Bolingbrook, Romeoville, Homer Glen, Plainfield and Lockport are inside the standard 50-mile radius of our Lake Bluff office. Joliet, New Lenox, Crest Hill, Mokena, Frankfort and Shorewood, at roughly 52 to 56 miles, are quoted case by case rather than turned away. Call (224) 220-3660 with your address and we will tell you what applies.

Do I need a permit for a Cummins generator in unincorporated Will County?

Yes. The county ordinance requires a permit in advance for electrical installations outside municipal limits and a permit for all electrical work, issues electrical permits only when a licensed and bonded electrical contractor is listed, and requires contractors to be registered, insured and bonded with the Land Use Department. Permits come from the Building Section in Joliet through the SmartGov portal; inside a city or village, that municipality issues the permit instead.

Does the county’s wiring rule change the installation?

In unincorporated Will County, sec. 150.110 requires copper wiring on the load side of the meter and EMT conduit throughout structures. Our electricians run the transfer switch and generator circuits to that standard, and we include it in the quote.

Will a Cummins generator run my sump pump and well pump?

Yes, and both belong on the load list in Will County: the county ordinance requires basements and crawl spaces to drain to a sump pump, and the Health Department permits private wells. The QuietConnect™ 13 kW covers both pumps along with the furnace, refrigerator and lights in most homes; the 17 kW and 20 kW add air conditioning.

Will Nicor need to upgrade my meter?

Sometimes. A Cummins 20 kW unit draws 255,947 BTU/hr of natural gas at full load on top of your existing appliances. We check the meter and service line before installation and arrange any Nicor upgrade; outside Nicor’s lines, every air-cooled QuietConnect™ runs on propane.

What affects the installed price in Will County?

The generator size, the transfer switch type, the county’s wiring and conduit requirements for unincorporated homes, the length of the gas run, a Nicor meter upgrade, the cold-weather option and whether the property is beyond our standard 50-mile radius. Every job is quoted after a free in-home estimate; see our Cummins installation and pricing page.

Which Cummins offers apply right now?

Ask GSHA about current Cummins offers. We confirm what applies to your generator and installation date at the estimate; financing is described on our financing page.

More Cummins pages

Authorized Cummins dealer in Northern Illinois (main page) · Cummins installation and pricing · Cummins generators · Cummins fault codes · Whole-house generator installation

Other counties

Request a free Cummins installation estimate

Tell us about your home and the generator you are considering in Will County. We will follow up to schedule a free, no-obligation in-home visit, count the loads you want carried, check the gas meter, electrical service and placement, and give you a written quote.

Send the form or call

Use the form here, book online, or call (224) 220-3660.

In-home visit

A GSHA advisor reviews your panel, gas meter and the proposed pad location and explains the Cummins options that fit.

Written quote

You receive an itemized quote with the generator, transfer switch, warranty registration, permits and the work included. No obligation.

If the form does not load, email info@gshaservices.com or call (224) 220-3660.

About GSHA Services, LTD

GSHA Services, LTD is a licensed and insured heating, cooling, electrical, plumbing and generator contractor and an authorized Cummins dealer for home standby generators. Offices: 1257 Cobblestone Way, Suite A, Woodstock, IL 60098 and 11 N Skokie Hwy, Lake Bluff, IL 60044. Phone (224) 220-3660. Email info@gshaservices.com. We install and service Cummins generators across the northern and western Chicago suburbs; see the full service area by ZIP code. Contact us · Financing · All products and brands

Sources

  1. Cummins Quiet Connect Series Specification Sheet NAS-6254 (RS13A, RS17A, RS20A, RS20AC) — https://mart.cummins.com/imagelibrary/data/assetfiles/0058055.pdf (accessed 2026-10-23)
  2. Cummins QuietConnect™ Series (home standby) — https://www.cummins.com/en-na/na/generators/home-standby/quietconnect-series (accessed 2026-10-23)
  3. Will County, Illinois (Wikipedia; 2020 Census populations, county population and area) — https://en.wikipedia.org/wiki/Will_County,_Illinois (verified by GSHA 2026-09)
  4. Nicor Gas, Where We Are — https://www.nicorgas.com/company/where-we-are.html (verified by GSHA 2026-09)
  5. Village of New Lenox, Guide for New Residents — https://www.newlenox.net/292/Guide-for-New-Residents (verified by GSHA 2026-09)
  6. Village of Homer Glen, Utilities — https://www.homerglenil.org/2485/Utilities (verified by GSHA 2026-09)
  7. Will County Land Use Department, Development Services Division: Building — https://willcounty.gov/County-Offices/Economic-Development/Will-County-Land-Use-Department/Development-Services-Division/Building (verified by GSHA 2026-09)
  8. Will County Building Ordinance sec. 150.003 — https://codelibrary.amlegal.com/codes/willcounty/latest/willcounty_il/0-0-0-47886 (verified by GSHA 2026-09)
  9. Will County Building Ordinance sec. 150.110 Electrical Requirements — https://codelibrary.amlegal.com/codes/willcounty/latest/willcounty_il/0-0-0-48224 (verified by GSHA 2026-09)
  10. Will County Building Ordinance sec. 150.070 (drain tile and sump pumps) — https://codelibrary.amlegal.com/codes/willcounty/latest/willcounty_il/0-0-0-48134 (verified by GSHA 2026-09)
  11. Will County Land Use Department, contractor registration FAQ — https://willcounty.gov/County-Offices/Economic-Development/Will-County-Land-Use-Department/Development-Services-Division/Building/FileId/1987 (verified by GSHA 2026-09)
  12. Will County Comprehensive Stormwater Management Plan (September 1998) — https://willcounty.gov/County-Offices/Economic-Development/Stormwater-Management-Planning-Committee/Plans-Projects/FileId/4021 (verified by GSHA 2026-09)
  13. Will County Health Department, Safe Water, Wells and Septic Systems — https://willcountyhealth.org/safe-water-wells-and-septic-systems/ (verified by GSHA 2026-09)
  14. Will County Land Resources Management Plan excerpts (2002) — https://willcounty.gov/County-Offices/Economic-Development/Will-County-Land-Use-Department/Community-Development-Division/Long-Range-Planning/FileId/2025 (verified by GSHA 2026-09)
  15. Will County news release, August 13, 2026: resources for residents impacted by storms — https://willcounty.gov/News/resources-available-for-will-county-residents-impacted-by-storms (verified by GSHA 2026-09)
  16. GSHA service area page — https://gshaservices.com/about-gsha-services/service-area/ (accessed 2026-10-23)