All-in-one comfort for condos, apartments and townhomes

Your Authorized MagicPak Dealer in Northern Illinois

GSHA Services, LTD is an authorized MagicPak dealer and installer with offices in Woodstock and Lake Bluff. Our own crews replace, install and service MagicPak all-in-one units, the self-contained heating and cooling cabinets that sit in a closet and breathe through a louver in the exterior wall, for condominium owners, apartment and townhome owners, associations and building managers in McHenry, Lake, Boone, Kane, DuPage, Cook and Will counties.

MagicPak (you will also see it written Magic-Pak or Magic Pak) makes gas-heat/electric-cool units, electric heat pumps and electric-heat/electric-cool units for multifamily buildings. Replacing one is not like swapping a furnace in a basement: the new unit has to fit the closet, the wall sleeve and louver, the vent through the wall, the gas line or electrical circuit, the ductwork and often the condominium association’s rules. Every GSHA MagicPak job starts with a free on-site estimate that checks all of those before we quote. Request a free estimate or call (224) 220-3660.

Request a free installation estimateCall (224) 220-3660

MagicPak M-Series single packaged vertical unit cabinet

Authorized MagicPak DealerGSHA Services, LTD · Woodstock & Lake Bluff, IL

An authorized MagicPak dealer with its own crews

Who makes MagicPak

MagicPak is a brand of Allied Air Enterprises LLC, which the MagicPak website identifies as a Lennox International Inc. company. MagicPak describes its products as single packaged vertical units (SPVUs) and packaged through-the-wall units: one cabinet holds the compressor, both coils, the blower, the controls and, on gas models, the burner and heat exchanger. Because nothing sits outside on a pad or a balcony, MagicPak units are common in mid-rise and garden condominiums, apartment buildings and stacked townhomes, where each unit has its own closet, its own wall louver and its own utility meter. (Source: magicpak.com.)

Our own crews, our own licensed electricians

The people who measure your closet, size the unit and install it work for GSHA. Gas piping, the through-wall vent and condensate drain, duct connections, permits and inspections, start-up and the owner walkthrough are handled by GSHA crews, and the electrical work, from the unit’s circuit and disconnect to the thermostat wiring, is done by GSHA’s own licensed electricians. GSHA also installs and services other brands, including split systems and ductless mini-splits, so if a MagicPak is not the best fit for a particular unit we will say so.

Working with owners, managers and boards

MagicPak replacements rarely happen in isolation. An owner may be replacing one failed unit, a landlord may be turning over an apartment, and an association may be planning a building-wide changeover so every louver on the facade matches. We quote each of those differently and can coordinate access, building rules and scheduling with the management company. Questions first? Call (224) 220-3660 or email info@gshaservices.com.

Current MagicPak offers

Ask GSHA about current MagicPak offers.

We did not find a current MagicPak consumer promotion on the manufacturer’s website when this page was published, so we do not advertise one here. If an offer becomes available for your unit and installation date, we will tell you at the estimate. Financing programs available through GSHA are on our financing page. See financing options.

Utility incentives depend on your utility, the equipment installed, the installation date and, in multifamily buildings, whether the owner, the landlord or the association applies. We check current eligibility with you during the estimate rather than promising a rebate up front.

Explore MagicPak products

MagicPak sells two families of all-in-one units, the M-Series and the V-Series, plus the wall sleeves and louvers they install through. Ratings shown are MagicPak published figures (most are maximums, written as up to) for the model family; the rating and capacity of your unit depend on the exact model and size installed.

Cutaway of a MagicPak gas heat and electric cooling M-Series unit

MGE9 gas/electric (95% AFUE)

The condensing M-Series gas unit. MagicPak rates it at 95% AFUE with up to 11.7 SEER2 and 10.5 EER2, and adds its patented FreezeShield protection, which circulates flue gas to keep condensate from freezing in winter.

M-Series · gas heat, electric cooling

Published specs
  • Gas heating input: 20,000 to 50,000 BTU/h
  • Cooling capacity: 12,000 to 30,000 BTU/h
  • Efficiency: 95% AFUE; up to 11.7 SEER2 and 10.5 EER2
  • Stainless steel five-pass primary heat exchanger; sealed burner box
  • Telescoping flue pipe that adjusts for different wall thicknesses (MagicPak describes it as patent-pending)
  • Designed for full indoor installation; top supply and return duct connections; certified for less than 2% cabinet air leakage

MagicPak published figures for the model family. The size and rating of your unit are confirmed at the estimate.

See the GSHA MGE product page

MGE8 gas/electric (80% AFUE)

The non-condensing M-Series gas unit, rated at 80% AFUE with up to 13.4 SEER2 and 10.6 EER2, in a wider size range than the MGE9: 0.75 to 3.0 tons of cooling.

M-Series · gas heat, electric cooling

Published specs
  • Gas heating input: 15,000 to 60,000 BTU/h
  • Cooling capacity: 9,000 to 36,000 BTU/h (0.75 to 3.0 tons)
  • Efficiency: 80% AFUE; up to 13.4 SEER2 and 10.6 EER2
  • Stainless steel heat exchanger; antimicrobial drain pan with overflow protection; toolless filter access

MagicPak published figures for the model family.

See the GSHA MGE product page
Cutaway of a MagicPak all-electric M-Series unit

MHP heat pump

The all-electric M-Series heat pump: it cools in summer and heats by heat pump in cooler weather, with electric heat to back it up. A common choice where the building has no gas service to each unit.

M-Series · electric heat pump

Published specs
  • Cooling capacity: 0.75 to 3.0 tons
  • Heat pump heating range: 8,600 to 31,000 BTUH
  • Electric heating: 3 to 10 kW (M-Series overview)
  • Efficiency: up to 13.4 SEER2, 10.6 EER2 and 6.7 HSPF2
  • Less than 1.4% cabinet air leak; IPX1 and IPX4 ingress-protection rated

MagicPak published figures for the model family.

See the GSHA MHP product page

MCE electric/electric

The M-Series unit with electric resistance heat and electric cooling. It is the simplest cabinet of the three and suits units with modest heating loads or buildings wired for electric heat.

M-Series · electric heat, electric cooling

Published specs
  • Cooling capacity: 0.75 to 3.0 tons
  • Electric heat: 0 to 10 kW
  • Efficiency: up to 13.4 SEER2 and 10.6 EER2
  • Less than 1.4% cabinet air leak; IPX1 and IPX4 ingress-protection rated

MagicPak published figures for the model family.

See the GSHA MCE product page

V-Series HWC gas/electric

MagicPak’s V-Series gas-heat, electric-cool unit, 1.0 to 2.5 tons of cooling at up to 13.4 SEER2 and 10.6 EER2, with front access to repairable parts.

V-Series · gas heat, electric cooling

Published V-Series features
  • Zero clearance design with access to all repairable parts from the front
  • Sloped exhaust pipe to reduce ice build-up on the louver and return condensate to the collector box
  • Heated condensate lines (a 24-volt heater keeps hoses at 35 to 40 F) and Freeze Shield protection against drain-trap blockage
  • Tested down to -35 F, according to MagicPak

MagicPak’s V-Series page lists conflicting AFUE figures for the HWC, so GSHA confirms the heating rating of the exact model from MagicPak literature before quoting.

Request an estimate for a V-Series unit

V-Series EWC electric/electric

The V-Series electric-heat, electric-cool unit: 1.0 to 2.5 tons of cooling with 5 to 15 kW of electric heat, up to 12.5 SEER2. MagicPak lists it as part of its R-410A product line, so we confirm current availability before quoting.

V-Series · electric heat, electric cooling

Published specs
  • Cooling capacity: 1.0 to 2.5 tons
  • Electric heat: 5 to 15 kW
  • Efficiency: up to 13.0 SEER / 12.5 SEER2
  • Shares the V-Series front-access, sloped-exhaust and heated-condensate design

MagicPak published figures for the model family.

Request an estimate for a V-Series unit

Wall sleeves and louvers

Each M-Series unit comes with a wall sleeve that seals the unit against heat and cold coming through the wall opening. Louvers, the grilles you see on the outside of the building, come in a range of colors and finishes, including custom paint.

M-Series and V-Series accessories

Why it matters on a replacement
  • The louver is part of the building facade, so associations often care about its color and finish
  • The sleeve, louver and vent opening must suit the new unit; GSHA checks them against MagicPak installation literature at the estimate
  • MagicPak also lists impact-rated accessories for coastal projects; these are not typically needed in northern Illinois
How GSHA handles the wall opening

Repair and maintenance

GSHA repairs and maintains MagicPak units whoever installed them: filters, condensate drains and traps, blowers, controls, gas and electrical components. When a unit is near the end of its life, we tell you whether a repair or a replacement makes more sense.

All MagicPak generations

Warranty basics
  • MagicPak lists a 5-year limited warranty on parts and a 20-year limited warranty on the stainless steel heat exchanger
  • MagicPak states that no registration is required for new single packaged vertical units
  • Claims are handled through a local MagicPak registered distributor
Call (224) 220-3660 for service

Choose a unit

In most MagicPak replacements the building has already made the biggest decision for you: whether each unit has its own gas line and vent, or runs on electricity alone. Within that, these are the choices GSHA walks through at the estimate.

Gas heat with electric cooling: MGE9, MGE8 or V-Series HWC

If your current unit has a gas line and a flue running out through the louver, a gas model is the usual replacement. The MGE9 is MagicPak’s condensing unit at 95% AFUE, meaning about 95 percent of the gas energy becomes heat over a season, and its FreezeShield design is aimed at the problem every condensing through-the-wall unit faces in a Chicago-area winter: keeping condensate from freezing at the wall. The MGE8 is the 80% AFUE non-condensing unit with a higher cooling efficiency rating (up to 13.4 SEER2 against the MGE9’s up to 11.7 SEER2) and a wider size range. Which one fits depends on the size the unit needs, the vent arrangement, whether a condensate drain can be run, and what the rest of the building uses.

All-electric heat pump: MHP

Where there is no gas to the unit, the MHP heat pump moves heat into the home in cooler weather instead of making it with resistance coils, and switches to its electric heat strips when it needs help. MagicPak rates the MHP at up to 6.7 HSPF2 for heating and up to 13.4 SEER2 for cooling. In northern Illinois the electric heat carries more of the load on the coldest days, so we size the electric heat as carefully as the cooling.

Electric heat with electric cooling: MCE or V-Series EWC

An MCE or EWC heats with electric resistance only. It is the simplest unit to service and suits interior units with small heating loads, or buildings whose electrical design was built around electric heat. If you are replacing an electric-heat unit and want lower heating costs, ask us to compare an MHP heat pump for the same closet; the decision depends on the electrical circuit and whether the heat pump fits the space.

Replacing an older MagicPak or another brand

Many buildings in our area still run original MagicPak units or other through-the-wall brands. We measure the closet, the wall sleeve and louver, the duct connections and the utility connections, then check them against current MagicPak installation literature. Sometimes a current unit fits the existing opening with new trim; sometimes the sleeve, louver or vent must change, which can affect the facade and therefore the association. We tell you which before you commit.

Sizing and compatibility are confirmed during the free estimate. GSHA reviews the heating and cooling load, the existing unit’s nameplate, the closet clearances, the vent and condensate path, gas service or the electrical circuit, and the ductwork, and quotes the specific MagicPak model in writing.

Why the installation matters

An all-in-one unit is factory-wired, charged and tested, which removes a lot of field work compared with a split system. What remains is exactly the work that decides whether the unit is quiet, dry and trouble-free for years. These are the steps GSHA performs on a MagicPak installation.

  • Measuring the closet and the opening. We record the closet dimensions, door and service clearances, the wall thickness and the existing sleeve and louver, because a unit that cannot be serviced from the front of the closet becomes expensive to maintain.
  • Sizing. We look at the unit’s floor area, exposure, windows and the existing equipment’s history instead of copying the old nameplate. An oversized unit short-cycles and leaves the space clammy in summer; an undersized one cannot keep up on the coldest nights.
  • Venting and freeze protection. On gas units the flue runs through the wall at the louver. MagicPak’s MGE9 uses a telescoping flue that adjusts for wall thickness and a flue tip designed to prevent ice bridging; we install the vent to MagicPak’s instructions and confirm it clears the louver properly.
  • Condensate. Every cooling unit makes water, and a condensing gas unit makes more in winter. We connect the condensate to the building drain or the path MagicPak’s instructions call for, check the trap and overflow protection, and make sure nothing drains onto a neighbor’s balcony or down the facade.
  • Gas and electrical. GSHA reconnects or modifies the gas piping with a shut-off at the unit, and our own licensed electricians confirm the circuit, breaker and disconnect match the new unit’s nameplate before it is energized.
  • Ducts and air sealing. MagicPak’s M-Series units connect to supply and return ducts at the top of the cabinet. We check the connections, seal them, and look for return-air problems that make a closet unit noisy.
  • Permits, building rules and inspection. GSHA pulls the municipal permit, follows the building’s rules for access, hours and protection of common areas, and schedules the inspection.
  • Start-up and handoff. We start the unit, run it through heating and cooling, check the thermostat, and show you where the filter is and how often to change it. MagicPak states that no warranty registration is required for new single packaged vertical units; we leave the model and serial numbers with your invoice.

Condominiums, associations and rentals

Multi-unit housing is a large share of the homes we serve. In the U.S. Census Bureau’s 2020-2024 American Community Survey, buildings with two or more homes make up about 54 percent of all housing units in Cook County, 29 percent in DuPage, 21 percent in Lake, 18 percent in Kane, 13 percent in Will, 12 percent in McHenry and 10 percent in Boone, and single-family attached homes such as townhomes add another 5 to 12 percent in each county. Each county page breaks those numbers down.

Who decides what

In a condominium, the HVAC unit inside your home is often the owner’s responsibility, while the exterior wall, the louver and shared building systems are often common or limited common elements controlled by the association. Which applies in your building is set by your association’s declaration, bylaws and rules, not by GSHA or by MagicPak, and it varies from building to building. Before we schedule a replacement, check with your board or management company whether you need written approval, a certificate of insurance from the contractor, or a matching louver color.

What we bring to the board

When an association asks, GSHA provides the proposed model and its MagicPak specification sheet, the louver finish, a description of any change to the wall opening or vent, our certificate of insurance and the permit once issued. For building-wide projects we can quote standard replacement scopes so owners and the board compare like with like.

Landlords and property managers

For rental units, the owner usually makes the decision and the tenant provides access. Nicor Gas runs a Multi-Family Savings program with energy assessments and rebates for owners and property managers of multi-family rental properties with three units or more; ask us whether your property is a candidate and check eligibility directly with Nicor Gas.

Find your county

GSHA installs and services MagicPak units from two offices: Woodstock (McHenry County) and Lake Bluff (Lake County). Crews travel from those offices into Boone, Kane, DuPage, Cook and Will counties. Each county page covers the share of multi-unit housing there, local permit offices, gas and electric utilities, and what to ask your association. The ZIP-code list is the definitive coverage map.

Questions and answers

Is it MagicPak or Magic-Pak?

The manufacturer writes the brand as MagicPak, usually with a registered-trademark symbol. Older paperwork, building documents and parts of our own site use Magic-Pak or Magic Pak; they all refer to the same Allied Air brand of all-in-one units.

What is a MagicPak unit, and how is it different from central air?

A MagicPak is a single packaged vertical unit: the heating, cooling and blower sections are in one cabinet inside a closet, and it draws outdoor air and rejects heat through a louver in the exterior wall. A central split system has an outdoor condenser on a pad or roof connected by refrigerant lines to an indoor coil and furnace or air handler. MagicPak points out that its all-in-one design avoids separate outdoor units, refrigerant line sets and external disconnects, which is why it is used in buildings where each home has no yard or roof of its own.

Can a new MagicPak go into my existing wall opening?

Often that is the goal, because keeping the opening avoids changes to the facade. Whether it works depends on the model and generation of your current unit, the sleeve and louver condition, the vent location and the closet dimensions. GSHA measures all of these and checks them against current MagicPak installation literature at the estimate, and the quote states plainly whether the sleeve, louver or vent needs to change.

Should I choose gas or a heat pump?

Start with what the building supports. If your unit has its own gas line and flue, an MGE9 or MGE8 keeps gas heat. If the building is all-electric, the MHP heat pump usually heats more economically than the MCE’s resistance heat in mild weather, but it needs the right circuit and the closet space. We price both where both are possible.

Will a MagicPak handle a northern Illinois winter?

MagicPak designs for cold climates: the MGE9’s FreezeShield circulates flue gas to keep condensate from freezing, and MagicPak says its V-Series is tested down to -35 F. Real-world comfort still depends on sizing, a properly installed vent and condensate path, and sealing around the sleeve, which is where GSHA’s installation work counts.

What refrigerant do current MagicPak units use?

MagicPak’s current M-Series literature (MCE, MHP and MGE) is labeled R-454B, and the MHP and MCE pages describe the line as 2025 low-GWP compliant. MagicPak lists the V-Series EWC as part of its R-410A product line. GSHA confirms the refrigerant and availability of the exact model before quoting.

Do I need a permit and association approval?

A permit is typically required to replace heating or cooling equipment, but the rules are set by your municipality, and GSHA pulls it for you; the county pages list what local building departments publish. Association approval depends on your declaration and rules; ask your board or manager before scheduling, and we will supply the documents they request.

What warranty comes with a MagicPak?

MagicPak lists a 5-year limited warranty on parts and a 20-year limited warranty on the stainless steel heat exchanger, and states that no registration is required for new single packaged vertical units. Full terms are in MagicPak’s literature; GSHA explains what applies to the model you are quoted.

Are there rebates for MagicPak units?

Ask GSHA about current MagicPak offers. Utility incentives are set by Nicor Gas, Peoples Gas, North Shore Gas, ComEd or a municipal utility, and each program defines the equipment it covers; whether a packaged through-the-wall unit qualifies under a given furnace, heat pump or multifamily program is something we check against the program rules for your address before you buy.

Do you service MagicPak units you did not install?

Yes. GSHA repairs and maintains MagicPak units regardless of who installed them, and we service other brands as well. Call (224) 220-3660 to schedule.

Request a free MagicPak installation estimate

Tell us about your home and the unit you are replacing. We will follow up to schedule a free, no-obligation visit, measure the closet and wall opening, check the vent, gas, electrical and ductwork, and give you a written quote.

Send the form or call

Use the form here, book online, or call (224) 220-3660.

On-site visit

A GSHA comfort advisor measures the unit, checks the existing installation and explains the MagicPak options that fit.

Written quote

You receive an itemized quote with the equipment, permits and the work included. No obligation.

If the form does not load, email info@gshaservices.com or call (224) 220-3660.

About GSHA Services, LTD

GSHA Services, LTD is a licensed and insured heating, cooling, electrical, plumbing and generator contractor and an authorized MagicPak dealer. Offices: 1257 Cobblestone Way, Suite A, Woodstock, IL 60098 and 11 N Skokie Hwy, Lake Bluff, IL 60044. Phone (224) 220-3660. Email info@gshaservices.com. We install and service MagicPak equipment across the northern and western Chicago suburbs; see the full service area by ZIP code. Contact us · Financing · Magic-Pak package units · Lennox split systems · All products and brands

Sources

  1. MagicPak home page (brand spelling; Allied Air Enterprises LLC, a Lennox International Inc. company) — https://www.magicpak.com/ (accessed 2026-10-23)
  2. MagicPak M-Series overview (MGE9, MGE8, MHP, MCE; wall sleeves; louvers) — https://www.magicpak.com/products/m-series (accessed 2026-10-23)
  3. MagicPak MGE9 product page — https://www.magicpak.com/products/m-series/mge9 (accessed 2026-10-23)
  4. MagicPak MGE8 product page — https://www.magicpak.com/products/m-series/mge8 (accessed 2026-10-23)
  5. MagicPak MHP product page — https://www.magicpak.com/products/m-series/mhp (accessed 2026-10-23)
  6. MagicPak MCE product page — https://www.magicpak.com/products/m-series/mce (accessed 2026-10-23)
  7. MagicPak V-Series overview (EWC, HWC) — https://www.magicpak.com/products/v-series (accessed 2026-10-23)
  8. MagicPak warranty page — https://www.magicpak.com/products/warranty (accessed 2026-10-23)
  9. MagicPak Where to Buy — https://www.magicpak.com/locate (accessed 2026-10-23)
  10. U.S. Census Bureau ACS 2020-2024 5-year, table B25024 Units in Structure, via Census Reporter (Boone, Cook, DuPage, Kane, Lake, McHenry and Will counties) — https://api.censusreporter.org/1.0/data/show/acs2024_5yr?table_ids=B25024&geo_ids=05000US17111,05000US17097,05000US17007,05000US17089,05000US17043,05000US17031,05000US17197 (accessed 2026-10-23)
  11. Nicor Gas Multi-Family Savings — https://www.nicorgas.com/ways-to-save/multi-family-savings.html (accessed 2026-10-23)
  12. Nicor Gas Residential Energy Efficiency Rebates — https://www.nicorgas.com/ways-to-save/residential-savings/rebates.html (accessed 2026-10-23)
  13. ComEd Home Heating & Cooling Discounts — https://www.comed.com/ways-to-save/for-your-home/rebates-discounts/heating-cooling-discounts (accessed 2026-10-23)
  14. GSHA Magic-Pak package units page — https://gshaservices.com/packaged-units-installation/magic-pak/ (accessed 2026-10-23)
  15. GSHA financing page — https://gshaservices.com/financing/ (accessed 2026-10-23)
  16. GSHA service area page (ZIP-code list) — https://gshaservices.com/about-gsha-services/service-area/ (accessed 2026-10-23)