Authorized Micro-Air dealer · Cook County, IL

Micro-Air EasyStart & EasySurge Dealer Serving Cook County, IL

GSHA Services, LTD is an authorized Micro-Air dealer and installer serving Cook County’s northern, northwestern and near-western suburbs, plus Tinley Park and Lemont. We have no office in Cook County: most work is dispatched from our Lake Bluff office, and the county’s northwest edge from Woodstock. Our own licensed electricians install the EasyStart Flex soft starter and the EasySurge Guardian surge protector on central air conditioners, heat pumps and, for surge protection, mini-splits.

Cook County’s housing is the oldest in our service area: the median home was built in 1961 and about 28 percent of housing units date from 1939 or earlier (U.S. Census Bureau, ACS 2020-2024). Older houses often have older electrical service and air conditioners added years after the house was built, so the AC circuit and disconnect get a careful look before anything is added. And in a county with many condominiums and two-flats, the right Micro-Air product depends on whether the system is a conventional central air unit or a variable-speed mini-split. Call (224) 220-3660 or request a free in-home visit.

Request a free installation estimateCall (224) 220-3660

Diagram: power from ComEd or Winnetka’s village utility, or from a generator, passes through the panel and transfer switch to the outdoor disconnect, where an EasySurge Guardian mounts, and on to an air conditioner fitted with an EasyStart Flex soft starterComEd orWinnetka utilityStandby orportable generatorPanel andtransfer switchFused disconnect+ EasySurgeGuardianAC orheat pump +EasyStart Flex
Where the two Micro-Air devices sit in a Cook County home. Diagram by GSHA Services.

Communities we serve in Cook County

Our service-area ZIP list covers Arlington Heights, Palatine, Des Plaines, Park Ridge, Mount Prospect, Prospect Heights, Wheeling, Rolling Meadows, Elk Grove Village, Schaumburg, Hoffman Estates and Streamwood in the northwest suburbs; Glenview, Northbrook, Morton Grove, Golf, Skokie, Wilmette, Kenilworth, Winnetka and Glencoe to the north; Franklin Park, Schiller Park, River Grove, Melrose Park, Hillside, Berkeley, Broadview and Westchester to the near west; and Tinley Park and Lemont to the south. Barrington, Buffalo Grove, Bartlett, Hanover Park and Elgin cross into neighboring counties, and we pull permits from whichever municipality your address belongs to.

Only some City of Chicago ZIP codes are on the list. We have worked at individual Chicago addresses, but Chicago homeowners should confirm their address first, as should residents of Cicero, Berwyn and other suburbs not on the list. The full list is on the service area page.

Why Micro-Air equipment makes sense in Cook County

Older homes, added-on air conditioning

Many Cook County houses were built before central air was common, so the air conditioner, its circuit and its disconnect were added later, sometimes more than once. A conventional single-stage or two-stage compressor on that kind of circuit is where the EasyStart Flex fits best: Micro-Air lists it for single-phase residential compressors up to 6 tons, including two-stage units and heat pumps, and rates it at up to a 75% reduction in start-up current. Less starting current means less light dimming when the compressor kicks on, and much less demand on a generator. Before adding it, our electricians make sure the circuit itself is right.

Condos, two-flats and mini-splits

More than half of Cook County’s housing units are in buildings with two or more units (ACS 2020-2024), and many all-electric condos and older homes use ductless mini-splits or variable-speed heat pumps. Those systems already ramp their compressors electronically and are not on Micro-Air’s EasyStart compatibility list, so a soft starter is usually not the tool. The EasySurge Guardian is different: Micro-Air designed it to protect any 240-volt HVAC equipment, including mini-splits and heat pumps. Condo work also needs the association’s approval for anything mounted outside.

Generators in the suburbs

About 80 percent of occupied homes heat with natural gas and 16 percent with electricity (ACS 2020-2024). For a gas-heated house with a standby or portable generator, the central air compressor is usually the hardest load to start. Micro-Air’s sizing guide assumes starting watts about 1.4 times running watts and no other significant loads running when the compressor starts, so we check the generator, transfer equipment and other loads before saying whether a soft starter will make the difference.

Surge and voltage protection

The EasySurge Guardian mounts outdoors next to the AC disconnect, suppresses surges with a 50 kA single-strike rating, and disconnects the outdoor unit when voltage goes above or below adjustable limits (125 to 280 volts high, 80 to 230 low). Its app shows line voltage in real time and keeps a 32-event log, which helps diagnose repeated trips on an older electrical service.

Permits and electrical rules in Cook County

Nearly every Cook County address is inside a municipality that issues its own permits; the Cook County Department of Building and Zoning covers only unincorporated areas and cannot process permits for Chicago or incorporated suburbs (e-Permits). When Micro-Air equipment goes in with a new air conditioner, heat pump or generator, it is covered by that project’s permit; for an add-on, we confirm with the local department and pull a permit when required. What the local offices publish:

  • Palatine. A permit is required for replacing or installing an air conditioning unit (when a permit is required), filed as an Express permit. The village’s 2026 AC handout requires a fused disconnect within sight of the unit and rigid conduit outdoors, and a final inspection with access to the electrical panel. An EasySurge Guardian goes next to that disconnect, in the same kind of conduit.
  • Arlington Heights. Air conditioner replacement in the rear yard is an over-the-counter permit; the AC guide asks for the contractor’s proposal and a site plan showing the unit’s location.
  • Des Plaines. Applications go through the city’s online portal (Building and Permits), and City Code 10-13-3 lists an HVAC/mechanical remove-and-replace permit for one- and two-family homes.
  • Park Ridge. A permit is required for heating and air conditioning work, and inspections are never same-day (Permits and Inspections).
  • Unincorporated Cook County. The county’s HVAC permit application requires a Cook County-registered HVAC contractor (Building and Zoning).
  • City of Chicago (confirm your address first). The Department of Buildings exempts only an in-kind replacement of an air conditioner of the same type, size and shape in a residential building up to four stories; other work needs a permit (Department of Buildings).

What our electricians check at the outdoor unit

On every Cook County job a GSHA electrician confirms the breaker against the outdoor unit’s nameplate, checks that the disconnect is fused or rated as the local code requires and is within sight of the unit, checks conduit and grounding, and looks at the panel the circuit comes from. The EasySurge Guardian mounts beside the disconnect with two half-inch conduit connections; the EasyStart Flex is wired between the supply and the compressor. Our HVAC technicians check the compressor, capacitor and contactor first, since a soft starter does not fix a failing part.

Electric utilities and outages in Cook County

ComEd delivers electricity everywhere in our Cook County service area except Winnetka, which runs its own water and electric utility; the Village of Winnetka appears on the American Public Power Association’s list of Illinois public power utilities. Winnetka residents report outages to the village; ComEd customers can check status on ComEd’s outage map.

The Micro-Air equipment works the same on either supply. We do not quote outage statistics; what matters here is what you want to run during an outage and whether your generator can start it.

Pairing Micro-Air with a generator in Cook County

We install home standby generators across our Cook County service area. The county generator pages cover gas utilities (Nicor Gas, North Shore Gas and Peoples Gas), permits and tight-lot placement: see KOHLER generator installation in Cook County, Generac in Cook County, Briggs & Stratton in Cook County and Champion in Cook County.

  • Small lot, smaller generator. On a narrow lot a compact generator may be the practical choice. A soft starter on the air conditioner can let that generator start it, if the running load fits.
  • Existing generator, new air conditioner. A larger compressor than the generator was sized for can be handled with a soft starter or load management in some cases.
  • Portable generator. It must connect through a transfer switch or interlock installed by our electricians. We tell you plainly whether central air is realistic on it.

Our generator installation page covers the process.

Micro-Air products we install in Cook County

The same two Micro-Air products are available county-wide. Full specifications are on the main Micro-Air page, and a shorter overview is on our EasyStart and EasySurge Guardian page.

EasyStart Flex

Soft starter for home air conditioners and heat pumps up to 6 tons; up to 75% less start-up current, per Micro-Air.

ASY-398-X1S-BL

EasyStart details

EasySurge Guardian

Surge and over/under-voltage protection for 240-volt HVAC equipment, including mini-splits, mounted beside the disconnect.

ASY-720-X01

EasySurge details

Generators

Standby generator installation across our Cook County service area.

KOHLER, Generac, Briggs & Stratton, Champion

Generators in Cook County

AC & heat pumps

New central air, heat pump and mini-split systems, with the Micro-Air add-ons quoted at the same visit.

Lennox, Carrier and other brands

AC and heat pumps in Cook County

Micro-Air offers

Ask GSHA about current Micro-Air offers.

Financing through our lending partners is described on the financing page.

Cook County questions and answers

Which GSHA office serves Cook County?

Most Cook County work is dispatched from our Lake Bluff office, and the county’s northwest edge from Woodstock. We have no office in Cook County.

I have a ductless mini-split in my condo. Which Micro-Air product fits?

Usually only the EasySurge Guardian. Mini-splits and other variable-speed systems already ramp their compressors and are not on Micro-Air’s EasyStart compatibility list, but Micro-Air designed the EasySurge Guardian for any 240-volt HVAC equipment, including mini-splits. Your condo association may need to approve anything mounted outside.

What does Palatine require at the outdoor unit?

Palatine’s 2026 AC handout requires a fused disconnect within sight of the unit and rigid conduit outdoors, with a final inspection that includes access to the panel. We install the EasySurge Guardian beside that disconnect to the same standard.

I live in Winnetka. Does the village electric utility matter?

Not for the Micro-Air equipment, which works on any 240-volt supply. Winnetka residents report outages to the village rather than ComEd.

Can you install Micro-Air equipment at a Chicago address?

Only some Chicago ZIP codes are on our ZIP list, so please confirm your address first. Chicago exempts only in-kind air conditioner replacements in buildings up to four stories from permits; we confirm what applies to other work.

Will a soft starter stop my lights from dimming?

It usually reduces the dimming, because Micro-Air rates the EasyStart Flex at up to 75% less start-up current and lists reduced light blinking among its benefits. If the dimming comes from a loose connection or an undersized service, we fix that first.

Other counties we serve

Back to the main Micro-Air page, or choose another county.

Request a free Micro-Air installation estimate

Tell us about your air conditioner, heat pump or mini-split in Cook County, your generator if you have one, and what you want to solve. We will follow up to schedule a free, no-obligation in-home visit, check the equipment and electrical circuit, and give you a written quote.

Send the form or call

Use the form here, book online, or call (224) 220-3660.

In-home visit

A GSHA technician reads the nameplates, checks the circuit and explains which Micro-Air products, if any, fit your goal.

Written quote

You receive an itemized quote with the equipment, any permit and the work included. No obligation.

If the form does not load, email info@gshaservices.com or call (224) 220-3660.

About GSHA Services, LTD

GSHA Services, LTD is a licensed and insured heating, cooling, electrical, plumbing and generator contractor and an authorized Micro-Air dealer and installer. GSHA Services is an independent company and is not Micro-Air, LLC; product warranties are provided by the manufacturer. Offices: 1257 Cobblestone Way, Suite A, Woodstock, IL 60098 and 11 N Skokie Hwy, Lake Bluff, IL 60044. Phone (224) 220-3660. Email info@gshaservices.com. See the full service area by ZIP code. Contact us · Financing · All products and brands

Sources

  1. Micro-Air, EasyStart Flex Home AC Soft Starter product page — https://www.microair.net/products/easystart-flex-home-ac-soft-starter (accessed 2026-10-23)
  2. Micro-Air Knowledge Bank, Sizing a Generator — https://www.micro-air.com/kb-easystart/article_presales/easystart_Selecting_a_Generator.htm (accessed 2026-10-23)
  3. Micro-Air, EasySurge Guardian HVAC Surge Protector product page — https://www.microair.net/products/easysurge-guardian-hvac-surge-protector (accessed 2026-10-23)
  4. Census Reporter, ACS 2020-2024 5-year tables B25024, B25034, B25035 and B25040, Cook County — https://api.censusreporter.org/1.0/data/show/acs2024_5yr?table_ids=B25024,B25034,B25035,B25040&geo_ids=05000US17031 (accessed 2026-09-16)
  5. Cook County, e-Permits — https://www.cookcountyil.gov/service/e-permits (accessed 2026-09-16)
  6. Village of Palatine, When a Building Permit is Required — https://www.palatine.il.us/621/When-a-Building-Permit-is-Required (accessed 2026-09-16)
  7. Village of Palatine, Express Building Permits — https://www.palatine.il.us/609/Express-Building-Permits (accessed 2026-09-16)
  8. Village of Palatine, 2026 AC Replacement handout (fused disconnect within sight, rigid conduit) — https://www.palatine.il.us/DocumentCenter/View/710/AC-Replacement-Handout-PDF (accessed 2026-09-16)
  9. Village of Arlington Heights, Over-the-Counter Permits — https://www.vah.com/over_the_counter_permits/index.php (accessed 2026-09-16)
  10. Village of Arlington Heights, Air Conditioning Replacement guide — https://www.vah.com/HVAC%20-%20Air%20Conditioning%20-%20Replacement.pdf (accessed 2026-09-16)
  11. City of Des Plaines, Building and Permits — https://www.desplainesil.gov/Departments/Community-and-Economic-Development/Building-and-Permits (accessed 2026-09-16)
  12. City of Des Plaines, City Code 10-13-3 — https://codelibrary.amlegal.com/codes/desplainesil/latest/desplaines_il/0-0-0-6936 (accessed 2026-09-16)
  13. City of Park Ridge, Permits and Inspections — https://www.parkridge.us/your_government/city_departments/permits_and_inspections_2.php (accessed 2026-09-16)
  14. Cook County, HVAC Permit Application — https://www.cookcountyil.gov/sites/g/files/ywwepo161/files/documents/2022-03/HVAC%20Permit%20Application%202022.pdf (accessed 2026-09-16)
  15. Cook County, Building and Zoning — https://www.cookcountyil.gov/agency/building-and-zoning-0 (accessed 2026-09-16)
  16. City of Chicago Department of Buildings, mechanical work not requiring a permit — https://www.chicago.gov/city/en/sites/guide-to-building-permits/home/help/faq/DOB/bldg-permit-not-required/worktype/mechanical.html (accessed 2026-09-16)
  17. Village of Winnetka, Water & Electric — https://www.villageofwinnetka.org/176/Water-Electric (accessed 2026-10-23)
  18. American Public Power Association, Public Power in Illinois — https://www.publicpower.org/public-power-illinois (accessed 2026-10-23)
  19. ComEd outage map — https://www.comed.com/outages/experiencing-an-outage/outage-map (accessed 2026-10-23)
  20. GSHA Services service-area page — https://gshaservices.com/about-gsha-services/service-area/ (accessed 2026-10-23)