Generac Overvoltage (1800) and Undervoltage (1900–1916) Alarms: What They Mean
Your Generac home standby generator started, ran for a little while, then shut down with Undervoltage or Overvoltage on the display or in the Mobile Link® app — maybe after saying WARMING UP for a few minutes. This page explains what the controller saw, why it happens, what you can safely do, and when to call a Generac technician.
- Authorized Generac dealer
- Generac-trained technicians
- Serving Chicagoland & southeastern Wisconsin
What the Overvoltage and Undervoltage alarms mean
A generator makes electricity by spinning a magnet (the rotor) inside coils of wire (the stator). The controller — the small computer behind the display — measures the voltage coming out and works to hold it steady near 240 volts. If the voltage climbs too high for too long, the controller stops the engine and shows Overvoltage. If the voltage drops too low, or never builds up after the engine starts, it shows Undervoltage.
Both are alarms, not warnings. Generac’s owner’s manuals explain the difference: a warning does not stop the generator; an alarm shuts it down to protect the system from damage. While either alarm is active, the generator will not start on its own during an outage and your home is not protected.
Which Generac models show these codes
The codes below come from Generac’s service manuals for air-cooled home standby generators with the Evolution 1.0 and 2.0 controllers and the newer PowerZone 200 controller. Older Nexus units show the words OVERVOLTAGE or UNDERVOLTAGE on the screen without a number, and their trip points are set a little differently from the Evolution codes below. If you have the Mobile Link app, the same alarm shows there too.
| Code | Alarm shown | What the controller saw | Controllers |
|---|---|---|---|
| 1800 | Overvoltage Alarm | Prolonged overvoltage — the output stayed too high. | Evolution 1.0 / 2.0, PowerZone 200 |
| 1801 | Overvoltage Alarm | Instantaneous overvoltage — a sudden jump in voltage. | PowerZone 200 |
| 1900 | Undervoltage Alarm | Prolonged undervoltage — output stayed below normal (80% of normal on Evolution units) for 10 seconds or more. | Evolution 1.0 / 2.0, PowerZone 200 |
| 1901 | Undervoltage Alarm | Instantaneous undervoltage — a sudden loss of voltage (less than 15 volts measured two seconds after start-up). | Evolution 1.0 / 2.0, PowerZone 200 |
| 1902 | Undervoltage Alarm | Both “zero crosses” missing for more than 1.5 seconds — the controller saw no usable voltage wave. Generac lists a faulty excitation winding or zero-cross circuit, loose wiring, or a field boost hardware failure as possible causes. | Evolution 1.0 / 2.0, PowerZone 200 |
| 1906 | Undervoltage Alarm | One zero cross missing for more than 1.5 seconds. Generac lists a faulty excitation winding, the zero-cross circuit or field boost hardware as possible causes. | Evolution 1.0 / 2.0, PowerZone 200 |
| 1907 | Undervoltage Alarm | After trying to shed load, the generator was still overloaded. | PowerZone 200 |
A “zero cross” is the moment the alternating-current wave passes through zero volts; the controller counts these to confirm the alternator is really making voltage. Generac groups the undervoltage alarms as the 1900 series. Codes 1903–1905 and 1916 appear in Generac’s liquid-cooled service manuals; air-cooled home standby units use 1900, 1901, 1902, 1906 and (PowerZone 200) 1907. If your display shows a different number, check your owner’s manual and give us the number when you call.
Why the display said “WARMING UP” first
The controller does not give up right away when voltage is low after a start. This applies to Evolution 1.0 units with firmware 1.12 or newer, all Evolution 2.0 units, and PowerZone 200 units. It keeps the engine running for up to about four minutes and shows WARMING UP on the display, or “Warming Up” in the Mobile Link app on the newest models. On some of the newest units, this extended warm-up depends on a setting your installer can enable.
Generac’s owner’s manual calls this a cleaning cycle. When the engine starts, the controller checks that voltage builds up properly. If frost crystals, dust or dirt are stopping a good electrical connection inside the unit, the start sequence pauses. The generator then tries to clean those internal connections by running. The service manual puts it this way: the extra run time gives the brushes and slip rings a chance to make a solid connection. (The brushes and slip rings are the parts that carry current to the spinning rotor.)
If the cleaning cycle works, the generator goes on to run normally and you may never notice. If not, the controller shuts down and shows Undervoltage. In AUTO, a PowerZone 200 unit restarts and checks for voltage twice more, about 15 seconds each time, before it shuts down on the alarm.
Why it happens
Undervoltage (1900 series) — most likely causes first
- A poor connection inside the generator. Frost, dust or dirt on the internal electrical connections — for example where the brushes ride on the rotor’s slip rings — can keep the voltage from building. Generac’s PowerZone 200 service manual adds that slip rings can pick up a tarnish or film while the unit sits idle, which can block the flow of current. This is what the warming-up cycle tries to clear on its own.
- Loose or damaged wiring. Generac lists loose wiring as a possible cause of code 1902. For that code, the service manual’s first step is to check the customer connections and the stator connections. During the alternator tests, the technician also confirms the harness connections at the stator terminal block are tight and secure.
- A field boost or excitation problem. When the engine reaches speed, the controller sends a short burst of current (called field boost or field flash) to the rotor to get voltage building. It switches off once the output has climbed to a set share of normal voltage. On PowerZone 200 units, and in Generac’s older Evolution/Nexus manual, that point is 80% of normal (192 volts on a 240-volt unit). The current Evolution manual gives a wider 40–80% window (90–192 volts) for Evolution 1.0 firmware 1.12 and newer and all Evolution 2.0 units. On Evolution 1.0 firmware before 1.12, field boost cut off at 88 volts or after 10 seconds, whichever came first. If the field boost circuit, its diode, or the alternator’s excitation winding fails, the voltage never comes up and the unit shuts down.
- The controller cannot “see” the voltage. The alternator may be making voltage. But if the small sensing wires that report voltage back to the controller are damaged, the controller reads low. It then shuts down for undervoltage even though the generator is working.
- A worn or failed alternator part. The rotor, brushes and slip rings, or the stator windings can fail with age. The service manual has the technician test these in order before replacing anything.
- Too much load at start-up. A generator that starts with a large load already connected cannot ramp up to its normal voltage. On Evolution units Generac has a separate code for this, Undervoltage Overload (2299). On PowerZone 200 units, code 1907 means the generator was still overloaded after it tried to shed load. A heavy load can also drag voltage and frequency down while the unit is running.
- The engine itself. Voltage depends on engine speed. If the engine is not holding its full 3,600 rpm — it hunts, runs rough or lacks power — the service manual sends the technician to engine and fuel diagnostics.
Overvoltage (1800 / 1801) — most likely causes first
- The engine is running too fast. Output voltage rises with engine speed. Once the service manual confirms the voltage is high, its next step is to check the output frequency. If the frequency is high, the technician checks the ignition coils (magnetos) and the speed signal wire the controller reads. Very high speed may also trip the separate Overspeed alarm (1200 series).
- Voltage regulation or calibration is off. If the frequency is normal but the voltage is not, the controller’s voltage calibration is checked. If the output is still out of range after calibration, the throttle (stepper motor) control is checked next. Like the Evolution controller, the PowerZone 200 has the automatic voltage regulator built into the controller. It changes the rotor’s excitation to hold a steady output as loads change, and the technician tests its output and sensing circuits on those units.
- A stator winding problem. In Generac’s older Evolution/Nexus service manual, the high-voltage flow chart ends with testing the stator, its insulation and the rotor.
What you can safely do
Generac’s owner’s manual gives the same homeowner answer for both alarms: contact an authorized service dealer. It also says an owner may clear an alarm and restart the generator once before calling. Steps 1, 5 and 6 below follow the manual. Steps 2 to 4 are general good practice that is safe with the unit OFF — they are not a Generac procedure.
- Write down the alarm and code. Note whether the display or app showed WARMING UP first, and whether the generator was powering the house (an outage), exercising, or being tested. Mobile Link shows the alarm and can send you an alert — a screenshot of that alert is helpful.
- If the display says WARMING UP right now, let it finish. This is the cleaning cycle described above. It can last several minutes. Do not press buttons or change modes while it is running.
- Turn off large loads. If the alarm came while a big appliance was starting — central air conditioning, an electric range, a well pump, a dryer — switch off what you do not need before you try again.
- Look, but do not open anything. From outside the unit, check for obvious damage. Look for a wiring conduit pulled loose between the generator and the transfer switch (the box that moves your house from utility power to generator power), or for chewed wires. If you see damage, skip the reset and call.
- Clear the alarm once. Press OFF. On Evolution and Nexus units, press ENTER to acknowledge the alarm. On the newest 10–28 kW units with the PowerZone 200 controller, press and hold OFF for at least three seconds, until the red OFF light is solid. Then press AUTO. Your owner’s manual shows the exact sequence for your model.
- If it comes back, stop. The owner’s manual says to stop trying to start it and contact a dealer. Repeated tries will not clear a wiring, excitation or alternator fault, and your home stays unprotected until it is fixed.
What a GSHA technician checks
- Controller firmware. The service manual says to confirm the controller has the latest firmware before troubleshooting an undervoltage, because newer firmware changed how the controller handles low voltage at start-up.
- What the controller sees versus what the generator makes. The technician opens the generator’s main breaker so no power reaches the house. Then they run the unit in MANUAL and compare the voltage on the display with the voltage measured at the breaker. The two readings together point to the field boost circuit, the excitation winding, the sensing wires, or the load side.
- The voltage-building parts. Field boost circuit and diode, excitation winding, rotor resistance, brushes and slip rings, and the stator windings and their insulation — tested in the manual’s order.
- Wiring connections at the generator’s customer connection area and at the stator terminal block, and the sensing wires back to the controller.
- Voltage and frequency under load, and the engine itself if it is not holding 3,600 rpm.
- For Overvoltage: output frequency and engine speed, ignition magnetos and the speed signal wire, voltage calibration, throttle (stepper motor) control, and on PowerZone 200 units the regulator output.
Because both alarms involve live output voltage, these tests are done by a trained technician with the right meters and with the unit under control — not a job for a homeowner.
When to call GSHA Services
- The same alarm came back after you cleared it once.
- The alarm showed up during a real outage, or the generator did not carry the house.
- Overvoltage (1800 or 1801) came back after one clear — there is nothing on the homeowner side to fix.
- WARMING UP appears at every weekly exercise or every start, even if the unit eventually runs.
- You see loose or damaged wiring, hear unusual noises, or smell fuel.
- It has been more than a year since the generator was serviced.
As an authorized Generac dealer, GSHA Services diagnoses and repairs Generac home standby generators and transfer switches using Generac service procedures and genuine parts. We handle warranty repairs on qualifying units and perform annual maintenance, so a cold-morning undervoltage does not become a no-start during the next storm. Learn more about our generator repair, generator tune-up and Generac generator installation services.
Request Generac service
Tell us the alarm and code (for example “Undervoltage 1902”) and whether the display showed WARMING UP. If you have it, add your generator model from the data plate and the best time to reach you. Our team will contact you to schedule a visit. For an urgent problem during an outage, please call (224) 220-3660.
Generac service area
GSHA Services is based in Woodstock, IL and services Generac generators across Chicagoland, including McHenry County and Lake County, and southeastern Wisconsin. Not sure if we cover your address? Call us or send the form above.
Related Generac codes
Frequently asked questions
What does Generac error code 1900 mean?
Code 1900 is Undervoltage. The generator was running but its output stayed below normal voltage (80% of normal on Evolution units) for 10 seconds or more, so the controller shut the engine down. Nearby codes 1901, 1902 and 1906 are also undervoltage shutdowns that describe how the voltage was lost. You may clear the alarm once; if it returns, a technician needs to test the alternator, excitation circuit and wiring.
Why does my Generac say WARMING UP and then shut down with Undervoltage?
WARMING UP is the controller giving the generator up to about four minutes to build normal voltage. Generac calls it a cleaning cycle: frost, dust or dirt on the internal electrical connections can block voltage from building, and running for a few minutes may clear it. If the voltage still does not come up, the controller stops the engine and shows Undervoltage. If this happens more than once, call for service.
What does Generac code 1800 Overvoltage mean?
Code 1800 means the generator’s output voltage stayed too high, so the controller shut the unit down to protect the generator and the connected system. On PowerZone 200 units, code 1801 is a sudden voltage spike. The usual causes are the engine running too fast or a voltage regulation or calibration problem. Generac’s owner’s manual tells homeowners to contact an authorized dealer for this alarm.
Can I reset a Generac undervoltage or overvoltage alarm myself?
Yes, once. Press OFF and acknowledge the alarm the way your owner’s manual describes. On Evolution and Nexus units, that means pressing ENTER. On the newest PowerZone 200 units, hold OFF for at least three seconds until the red OFF light is solid. Then press AUTO. If the same alarm comes back, stop and call a Generac technician.
Will my generator still run during an outage with an Undervoltage alarm showing?
No. Undervoltage and Overvoltage are alarms, not warnings. The generator stays shut down until the alarm is cleared, so it will not start on its own when the power goes out. Get it looked at before the next storm.
Generac® and Mobile Link® are trademarks of Generac Power Systems, Inc. GSHA Services, LTD is an authorized Generac dealer. This page is general guidance for homeowners; always follow the safety instructions in your owner’s manual and on the unit.
