← All Generac error codes
Generac® alarms & errors · Authorized Generac dealer

Generac Overspeed Alarm (Codes 1200–1207): What It Means and What to Do

Your Generac home standby generator shut itself down and a red light is on or flashing. The display or the Mobile Link app shows Overspeed, often with code 1200, 1205 or 1207. This page explains what the alarm means in plain language. It also explains why this is not a do-it-yourself repair, and the one safe step you can take before you call.

  • Authorized Generac dealer
  • Generac-trained technicians
  • Serving Chicagoland & southeastern Wisconsin
In short: Overspeed means the engine ran faster than it should. The controller (the generator’s small computer) shut it down to protect the engine and the alternator (the part that makes the electricity). Clear the alarm once (OFF, then AUTO); if it comes back, or if you heard the engine racing, call GSHA Services at (224) 220-3660.
Safety first. Never open the generator or touch wiring while it is set to AUTO — it can start on its own at any time. If you smell gas, leave the area and call your gas utility or 911 from a safe place. Never run a generator indoors, in a garage, or near an open window, and keep a working carbon monoxide alarm in your home.

What the Generac Overspeed alarm means

A Generac air-cooled standby generator is designed to run at a steady 3,600 rpm. That is revolutions per minute: how many times the engine turns each minute. On a 60 Hz unit, that speed produces the 60 Hz electricity your home uses. Hz stands for hertz, the number of cycles per second in household power. While the engine runs, the controller keeps track of engine speed. If the engine runs too fast, the controller shuts the engine down and records an Overspeed alarm.

How the controller reads speed depends on the model. On Evolution and older Nexus units, the speed signal comes from the engine’s ignition system. When the controller sees an overspeed, it turns off the ignition and closes the fuel shutoff valve, and the engine stops. Generac’s service manuals for these units say this protects the engine and the alternator from a damaging overspeed. On PowerZone 200 units, the engine control module (a second small computer that manages the engine) reports engine speed to the controller. The controller uses that reading to watch for overspeed.

Because it is an alarm (not a warning), the generator stays shut down. On current units the outside light flashes red; older units turn on a red Alarm light and show the alarm on the screen. Either way, the unit will not start in AUTO during a power outage until the alarm is cleared. If the cause is still there, it will simply shut down again.

What each overspeed code means

CodeAlarm shownWhat the controller sawControllers that show it
1200Overspeed
Alarm
A prolonged overspeed: the engine ran above about 72 Hz (around 4,320 rpm, roughly 20 percent faster than normal) for 3 seconds. On Evolution units, Generac lists a stepper motor/mixer assembly problem as the possible cause.Evolution 1.0, Evolution 2.0, PowerZone 200
1205Overspeed
Alarm
An instant overspeed: the engine spiked above about 75 Hz (around 4,500 rpm, roughly 25 percent faster than normal) for even a tenth of a second. Same possible cause as 1200.Evolution 1.0, Evolution 2.0, PowerZone 200
1207Overspeed
Alarm
An overspeed of 4,500 rpm or higher for 150 milliseconds, measured from the alternator’s output. The controller uses this backup method when it is not seeing the normal ignition pulses.Evolution 2.0 (older Evolution service manuals list it too)
1208Overspeed
Alarm
An overspeed the controller measured from a winding inside the alternator: above 75 Hz for half a second. Generac’s manual has the technician confirm the controller and engine firmware (the built-in software) and diagnose any other codes first.PowerZone 200 only
—Overspeed
Alarm
Older Nexus controllers show the word Overspeed on the screen without a number. The meaning and the repair path are the same.Nexus

Thresholds above are for 60 Hz units as listed in Generac service information. One older Generac service manual also lists code 1201 under the Overspeed alarm, with the same repair path. Evolution, PowerZone 200 and Nexus are the names of the controller (the control panel) used on different generations of Generac air-cooled units. Your model, controller and firmware version may word the alarm slightly differently.

Why it happens

Unlike many alarms, overspeed has no simple outside cause such as a closed gas valve or leaves in the vents. The parts involved are inside the unit. Generac’s service manuals name a possible cause for each code, and their repair steps check these areas, most likely first:

  1. The stepper motor and mixer assembly (Evolution units). The mixer is the part where gas and air are blended before they go into the engine. Part of the mixer assembly is a stepper motor, a small electric motor that moves the throttle plates (the flaps that control how much fuel and air reach the engine). While the generator runs, the controller uses this motor to open or close the throttle as your home’s power use changes. That keeps the engine speed and the frequency steady. For codes 1200 and 1205, Generac lists a stepper motor or mixer problem as the possible cause, and the technician checks the linkage and throttle plates for binding.
  2. The plug between the controller and the stepper motor. If the motor does not move when it should, Generac’s test has the technician make sure this plug is fully seated and its pins are not damaged.
  3. The controller itself. If the stepper motor’s coils (the wire windings inside the motor) test good but the motor still will not move on command, Generac’s procedure replaces the controller.
  4. Code 1207 on Evolution 2.0 units. This code comes from the controller’s backup speed check, described in the table above. For this code, Generac’s repair path checks the speed signal wire and the ignition magnetos (the parts that make the spark).
  5. The throttle and mixer assembly on PowerZone 200 units. The newest controller works with an electronic throttle control valve, an electronic mixer control valve and the engine control module. Generac’s engine speed test for these units checks for an overload and for an obstruction or damage in the throttle and mixer assembly.

None of these are things you can check from outside the enclosure (the generator’s cabinet). None of them are fixed by resetting the alarm again and again.

Why overspeed matters for your appliances

The speed of the engine sets the frequency of the electricity the generator makes. Generac’s service manual ties the two together directly: a 60 Hz unit makes 60 Hz power when the engine turns at 3,600 rpm. When the engine races, the frequency climbs right along with it. Code 1205, for example, trips at 75 Hz, a full 25 percent above normal.

Household power in the U.S. is 60 Hz, and most home equipment is designed for it. As a general rule in electrical work, power at the wrong frequency can be hard on motors and electronics. The reason Generac gives for the overspeed shutdown is to protect the engine and the alternator, and the controller acts within seconds. Either way, the shutdown is doing its job. What you do not want is to keep clearing the alarm and letting the engine race again.

What you can safely do

  1. Write down the alarm name and code, or take a photo of the display. If your generator is connected to Mobile Link, the app shows alarms and warnings too. On units with a screen, the controller’s History menu has an Alarm Log of recent alarms. The button path varies by model, so check your owner’s manual.
  2. Leave the inside of the unit alone. Do not open the enclosure, touch the throttle linkage, or unplug any connector. The generator can start on its own in AUTO, and the throttle parts need a technician’s tests, not a homeowner’s hands.
  3. Clear the alarm once. On the newest air-cooled units, press and hold OFF for at least 3 seconds, until the red OFF light stays on steadily. On older Evolution units with a screen, press OFF and then ENTER. Some manuals say ENTER twice, so check your owner’s manual for the exact keys on your unit. Then press AUTO so the generator is ready for the next outage.
  4. If the alarm comes back, stop. Do not clear it a second time. Generac’s owner’s manual allows an owner to clear an alarm once; for Overspeed, its troubleshooting chart says to contact an authorized service dealer. If you heard the engine surging or racing before it shut down, call us even if the alarm clears.
  5. Tell us what changed. Recent service, a recent storm or power flicker, a switch between propane and natural gas, or new large appliances are all useful clues.
Remember: while an alarm is active or the unit is in OFF, your home is not protected during a power outage. Rather than leave it that way, call us so we can find the cause and get it back in AUTO.

What a GSHA technician checks

Our technicians follow Generac’s diagnostic procedures for the Overspeed alarm and add a final check of our own. In plain terms, here is what that visit looks like:

  • Read the alarm history. On Evolution units, the technician reviews the controller’s Alarm Log. On PowerZone 200 units, the technician records every code shown in Generac’s Field Pro dealer app and works on any throttle, mixer or fuel codes first.
  • Watch the stepper motor sweep. The technician first confirms the controller shows the correct generator model. Then the unit is set to run, and the stepper motor should move the throttle through a full sweep and settle at its starting position. If it does not move, the plug and pins at the controller are checked.
  • Check the throttle by hand and test the motor. The technician moves the throttle linkage by hand to feel for binding or a damaged throttle plate, then measures the motor’s coils against Generac’s specification. A mechanical problem or an out-of-spec reading means the mixer assembly is replaced. A motor that tests good but will not move on command points to the controller.
  • Code-specific checks. For code 1207, the technician tests the engine speed signal wire and the ignition magnetos. On PowerZone 200 units, the technician watches the electronic throttle sweep and set itself for starting, then starts the unit to see whether the code returns.
  • Test-run the unit. Our own final check: run the generator and confirm the output frequency is in the normal 59–61 Hz range from Generac’s frequency test. Then put the unit back in AUTO.

A note on code 2399: Stepper Overcurrent

Stepper Overcurrent is a related alarm listed for many Generac air-cooled units; Evolution controllers show it as code 2399. It means the electrical current flowing through the stepper motor’s coils went above specification. That is the same small motor that moves the throttle, so the diagnosis follows the same path as an overspeed. The technician tests the stepper motor and mixer assembly and confirms the controller has the latest firmware. The mixer assembly or the controller is then replaced as the tests show. Generac’s owner’s manual says to contact an authorized service dealer for this alarm. There is no homeowner fix: clear it once, and call if it returns.

When to call GSHA Services

  • The Overspeed alarm (code 1200, 1201, 1205, 1207 or 1208, or the word Overspeed on a Nexus screen) came back after you cleared it once.
  • You heard the engine racing or surging before it shut down, even if the alarm cleared.
  • You see Stepper Overcurrent (2399).
  • The alarm cleared, but you want the cause found before the next outage. Generac’s owner’s manual lists contacting a dealer for Overspeed.
  • The generator did not start during an outage, or you are not sure it is ready for the next one.

As an authorized Generac dealer, GSHA Services diagnoses and repairs Generac home standby generators using Generac service procedures and genuine parts. That includes the mixer and stepper motor assemblies involved in this alarm, and warranty repairs on qualifying units. Regular generator maintenance is the best way to catch problems before the next storm. Learn more about our generator repair service and Generac generators.

Request Generac service

Tell us the alarm and code you see (for example “Overspeed 1205”), your generator model from the data plate if you have it, and the best time to reach you. Our team will contact you to schedule a visit. For an urgent problem during an outage, please call (224) 220-3660.

Generac service area

GSHA Services is based in Woodstock, IL and services Generac generators across Chicagoland, including McHenry County and Lake County, and southeastern Wisconsin. Not sure if we cover your address? Call us or send the form above.

Frequently asked questions

What does Generac error code 1200 mean?

Code 1200 is a prolonged Overspeed alarm. The controller saw the engine running above about 72 Hz, roughly 20 percent faster than its normal 3,600 rpm, for 3 seconds, and shut it down. On Evolution units, Generac lists the stepper motor/mixer assembly that controls the throttle as the possible cause, so it needs a service technician.

What is the difference between Generac codes 1200, 1205 and 1207?

All three are Overspeed alarms. Code 1200 means the engine ran too fast for 3 seconds. Code 1205 means it spiked even faster, above about 75 Hz, for a tenth of a second. Code 1207, listed for Evolution 2.0 controllers, is an overspeed of 4,500 rpm or more for 150 milliseconds that the controller measured from the alternator’s output. It uses that backup method when it is not seeing the normal ignition pulses. The action for the homeowner is the same for all three: clear it once, and call if it returns or if you heard the engine racing.

Can I reset a Generac overspeed alarm myself?

You can clear it once. On the newest units, press and hold OFF for at least 3 seconds until the red OFF light stays on steadily. On older Evolution units with a screen, press OFF and then ENTER; check your owner’s manual for the exact keys on your unit. Then press AUTO. If the alarm comes back, do not keep clearing it. If you heard the engine racing, call us even if the alarm clears. The parts Generac links to overspeed are inside the unit and need a technician.

Can an overspeed alarm damage my appliances?

The alarm itself is a protective shutdown. The concern is the overspeed behind it. Engine speed sets the frequency of the power the generator makes, and most home equipment in the U.S. is designed for 60 Hz. As a general rule in electrical work, power at the wrong frequency can be hard on motors and electronics. The controller shuts the engine down within seconds, and the reason Generac gives is to protect the engine and the alternator. That is why the alarm should be repaired rather than reset over and over.

What does Generac code 2399 Stepper Overcurrent mean?

Code 2399 is Stepper Overcurrent. It means the current flowing through the coils of the stepper motor (the small motor that moves the throttle) was above specification. It involves the same throttle control parts as an overspeed alarm, and Generac’s owner’s manual says to contact an authorized service dealer.

Generac® and Mobile Link® are trademarks of Generac Power Systems, Inc. GSHA Services, LTD is an authorized Generac dealer. This page is general guidance for homeowners; always follow the safety instructions in your owner’s manual and on the unit.