← All Generac error codes
Generac® alarms & errors · Authorized Generac dealer

Generac Underspeed Alarm (Codes 1600–1603): What It Means and What to Do

Your Generac home standby generator shows “Underspeed” with a code such as 1600 or 1603, and it has shut down. This page explains what the alarm means in plain language and why it usually happens. It also covers the safe checks you can do yourself and when to call a Generac technician.

  • Authorized Generac dealer
  • Generac-trained technicians
  • Serving Chicagoland & southeastern Wisconsin
In short: Underspeed means the engine could not reach or hold its normal running speed, so the generator shut itself down to protect the engine. The most common reasons are too much electrical load, a fuel supply that is low or weak, and a problem with the throttle control. Turn off large appliances, check your fuel, and clear the alarm once; if it comes back, call us.
Safety first. Lifting the lid to reach the buttons is fine, but never remove panels or touch wiring, even in OFF — some parts inside stay powered. A generator in AUTO can start on its own at any moment. If you smell gas, leave the area and call your gas utility or 911 from a safe place. Generator exhaust contains carbon monoxide: never run a generator indoors or near open windows, and keep a working carbon monoxide alarm in your home.

What the Underspeed alarm means

The electricity in your home runs at 60 hertz (Hz), a measure of how fast the current cycles back and forth. A home standby generator makes 60 Hz power by spinning its engine at a steady 3,600 revolutions per minute (RPM). The generator’s control system — the small computer that runs the unit — watches engine speed the whole time it runs. When the speed falls too far below where it should be, it stops the engine and posts an Underspeed alarm.

Underspeed is an alarm, not a warning. That matters: a warning lets the generator keep running, but an alarm shuts it down and keeps it from starting on its own. Until the alarm is cleared, your home will not switch to generator power during an outage. The red Alarm light on the unit is on (on the newest PowerZone 200 units it flashes about once a second). If your unit has Mobile Link®, the same alarm shows in the Mobile Link app.

On air-cooled Evolution controllers there are two versions of this alarm:

CodeAlarm shownWhat it means in plain words
1600Underspeed
Alarm
The engine was running but got dragged down and stayed too slow. There are three usual reasons. The generator may be overloaded (asked for more power than it can make). The fuel supply may be low. Or there may be a throttle control problem; the throttle sets how much fuel and air the engine gets. On a 60 Hz air-cooled Evolution unit, this alarm trips when the output sags to about 55 Hz for 30 seconds.
1603Underspeed
Alarm
The engine never reached its normal 3,600 RPM. The first suspect is the throttle control: the stepper motor and mixer that meter fuel and air into the engine.

Which generators show these codes? The table above covers Generac air-cooled home standby generators with Evolution 1.0 and Evolution 2.0 controllers. The newest air-cooled units with the PowerZone 200 controller use only Underspeed 1600, which simply means the unit could not run at its operating speed. Larger liquid-cooled Generac units with Evolution controllers use three Underspeed codes. They are 1600 (unit overloaded or a fuel system issue), 1601 (low fuel pressure) and 1602 (throttle stuck closed or nearly closed). Air-cooled units do not use 1601 or 1602, and liquid-cooled units do not use 1603. Older Nexus controllers do not use E-codes. The 2010 Nexus owner’s manual lists an “Under-frequency” protection rather than “Underspeed”; if you have a Nexus unit, call us with your model number.

Why it happens (most likely first)

1. The generator is overloaded

For code 1600, this is the first thing to suspect. Every generator has a limit to how much power it can supply. When your home asks for more than that, the engine slows down under the strain and the generator shuts off. That can happen when several big appliances run at once, such as the central air conditioner, an electric dryer, an electric range and a water heater. Generac Load Managers can help keep this in check. They are add-on devices that hold off large loads when they start and drop them to help an overloaded generator recover. If your generator also shows an Overload – Remove Load (2100) alarm, it is a sign the house is asking for more power than the generator can make.

2. Fuel supply is low or pressure is weak

The engine needs a steady supply of natural gas or propane at the right pressure to make full power. A low fuel supply is one of the listed causes of this alarm. The service manual also warns that a unit can start and run normally without load even when the wrong fuel type is selected. That is why the technician confirms the fuel setting matches the fuel you use (natural gas or propane). Gas pressure can also drop or bounce. Two causes are a gas pipe that is too small and a regulator (the device on the gas line that sets the pressure) mounted too close to the generator. If you use propane, check the tank level regularly, especially before storm season.

3. Throttle control problem

On Evolution units, a small electric motor called the stepper motor opens and closes the throttle to hold engine speed as your loads change. It moves the throttle through the mixer linkage, a small arm on the mixer (the part where fuel and air blend before entering the engine). If the motor, its wiring connector or the linkage is sticking, damaged or blocked, the engine cannot reach or hold 3,600 RPM. This is the first check for code 1603. PowerZone 200 units use an electronic throttle valve run by the engine control module (ECM, the engine’s own small computer) instead. A technician tests that valve and the sensor that reports how far it is open.

4. The engine is not making full power

A dirty air filter, worn spark plugs, an ignition problem or low compression (worn engine parts that let pressure leak out of the cylinders) can all leave the engine short on power. The unit may sound rough, hunt up and down, or backfire. These are engine-service items a technician checks during a repair or generator tune-up.

5. A shorted circuit or alternator problem

Less often, a short in one of the circuits the generator feeds pulls the engine down, even when the normal loads are not too big. A fault in the alternator can do the same. The alternator is the part of the generator that turns engine power into electricity, and its power windings are the coils of wire inside it. This shows up as both voltage and frequency dropping when loads are applied, and it takes a technician with a meter to find.

What you can safely do

These steps are safe to do without opening any panels. If you are not comfortable with any of them, skip to requesting service.

  1. Write down the code and when it happened. Open the Mobile Link app, or look at the controller display (Evolution units). Note the code number and what was running in the house at the time (air conditioner, dryer, range). PowerZone 200 units have lights and buttons instead of a screen, so the code shows in the app. If your unit is not connected, note which lights are on. This helps our technician arrive prepared.
  2. Lighten the load. This will not fix every Underspeed alarm, but overload is a common cause, so it gives the generator its best chance. Turn off or turn down the biggest electrical users you do not need during an outage: central air conditioning, electric range or oven, clothes dryer, electric water heater, hot tub. Leave the refrigerator, furnace, lights and a few outlets.
  3. Check your fuel. If you use propane, look at the tank gauge and have it filled if it is low. For natural gas or propane, make sure the shut-off valve on the gas line to the generator is fully open. Do not adjust the regulator.
  4. Look around the unit. Make sure leaves, snow, grass clippings or nests are not blocking the air intake and exhaust openings on the enclosure.
  5. Clear the alarm once. Evolution controllers (with a screen on the unit): press OFF, then ENTER to clear the alarm, then press AUTO. PowerZone 200 units (lights and buttons, no screen): press and hold OFF for at least 3 seconds until the red light stops flashing and stays solid, then press AUTO. Your owner’s manual shows the exact sequence for your model.
  6. Confirm the green light is on. In AUTO with utility power present, the green “Ready” light should be lit. That tells you the generator is back in AUTO and will try to start in the next outage. It does not mean the cause is fixed. If your unit’s lights look different, your owner’s manual shows what Ready looks like on your model.
  7. If the alarm comes back, stop. Do not keep clearing it. Call us or send the form below.
About code 1603. Generac’s owner’s manuals say to contact a dealer for any Underspeed alarm, 1600 or 1603. With 1603, the first check is the throttle control, which is technician work, so plan on a service visit. You can still clear the alarm once so the unit is back in AUTO.

What a GSHA technician checks

  • Actual load on the generator. With your normal circuits on generator power, we measure the current with a clamp meter, a meter that reads the current in a wire without disconnecting it. We compare the reading with the unit’s rating. If the house is asking for too much, we show you which circuits to shed. We also talk through load management and whether the generator is sized for the loads you want to run.
  • Fuel supply and pressure. We measure gas pressure at the generator with a manometer (a gas-pressure gauge), both at rest and while it runs under load. We also confirm the fuel setting, regulator placement and pipe size match Generac’s installation requirements. Pressure that drops or bounces under load can point to the gas supply, not the generator.
  • Throttle control. On Evolution units we watch the stepper motor sweep the throttle on start-up, check the mixer linkage for sticking or damage, and test the motor and its connector. On PowerZone 200 units we test the electronic throttle valve and its position sensor.
  • Engine condition. Air filter, spark plugs, ignition and compression — anything that would leave the engine short on power under load.
  • Voltage and frequency under load. If both drop while the load is within the rating, we check for a shorted load circuit and test the alternator’s power windings.
  • Alarm history. On PowerZone 200 units we read the alarm history in Generac’s service app to see whether a throttle or fuel-pressure fault was logged at the same time.

When to call GSHA Services

  • The Underspeed alarm comes back after you cleared it once.
  • You see code 1603 (engine never reached full speed).
  • The alarm comes back when a large appliance such as the air conditioner turns on, even with other big loads off.
  • Your propane tank is full and the gas valve is open, but the alarm still appears.
  • The engine surges, hunts, runs rough or backfires before it shuts down.
  • It has been more than a year since the generator was serviced.

As an authorized Generac dealer, GSHA Services diagnoses and repairs Generac home standby generators and performs annual maintenance, which helps catch problems like this before the next storm. Learn more about our generator repair, generator maintenance and Generac generator installation services.

Request Generac service

Tell us the alarm code (for example 1600 or 1603), what was running when it shut down, and the best time to reach you. If you can, add your generator model from the data plate (the label on the unit with the model and serial number). For an urgent problem during an outage, please call (224) 220-3660.

Generac service area

GSHA Services is based in Woodstock, IL and services Generac generators across Chicagoland, including McHenry County and Lake County, and southeastern Wisconsin. Not sure if we cover your address? Call us or send the form above.

Frequently asked questions

What does Generac error code 1600 mean?

Code 1600 is the Underspeed alarm. The engine was running but slowed down too much and stayed slow, so the generator shut itself off. The usual causes are an overloaded generator, a low fuel supply or a throttle control problem. Turn off large loads, check your fuel, and clear the alarm once. If it returns, call a Generac technician.

What does Generac error code 1603 mean?

Code 1603 is also an Underspeed alarm, used on air-cooled Evolution controllers. It means the engine never reached its normal running speed of 3,600 RPM. The first check is the throttle control (stepper motor and mixer). Clear the alarm once so the unit is back in AUTO, then schedule service.

Why does my Generac show Underspeed when the air conditioner turns on?

An air conditioner is a large electrical load. If the generator is already carrying most of its rating, adding the air conditioner can overload it, the engine slows, and the generator trips Underspeed. Turning off other large loads often helps. A Generac notice for units with a built-in load management controller says an air conditioner powered by the generator must be connected through that controller. A technician can check this and whether the generator is sized for the loads you want to run.

How do I clear a Generac Underspeed alarm?

On Evolution controllers, press OFF, then ENTER to clear the alarm, then press AUTO. On newer PowerZone 200 units, press and hold OFF for at least 3 seconds until the red light stops flashing, then press AUTO. Clear it only once. If the same alarm comes back, the problem needs a technician.

Can a low propane tank cause an Underspeed alarm?

Yes. A low fuel supply is one of the listed causes of the Underspeed alarm, along with overload and throttle control problems. The engine needs enough gas at the right pressure to make full power. Check your propane level and make sure the gas shut-off valve is fully open. Gas pressure and regulator checks are technician work.

Generac® and Mobile Link® are trademarks of Generac Power Systems, Inc. GSHA Services, LTD is an authorized Generac dealer. This page is general guidance for homeowners; always follow the safety instructions in your owner’s manual and on the unit.