← All Generac error codes
Generac® alarms & errors · Authorized Generac dealer

Generac “Service Schedule A / B” and Maintenance Reminders: What They Mean

Is your Generac home standby generator showing “Service Schedule A” or “Service Schedule B” on the screen? Or a yellow light (flashing on newer units) and a “Service A / Service B” alert in the Mobile Link® app? The controller — the small computer under the lid that runs the generator — is telling you routine maintenance is due. It is a reminder, not a breakdown. Here is what each schedule includes, why the message appears, and how to get it taken care of.

  • Authorized Generac dealer
  • Generac-trained technicians
  • Maintenance, repair & warranty service on Generac home standby models
  • Serving Chicagoland & southeastern Wisconsin
In short: “Service Schedule A” means an oil change, a new oil filter and a battery check are due — Generac sets that point at every 2 years or 200 run hours, whichever comes first. “Service Schedule B” adds the air filter and spark plugs at every 4 years or 400 hours, plus a valve-clearance check (a small engine gap a technician measures) on engines that need it. The generator still runs while the reminder shows; book a generator tune-up and the reminder is cleared after the work.
Safety first. A generator in AUTO can start on its own at any time, without warning. You may lift the lid to read the screen and press the control-panel buttons, but never remove a panel, reach inside or touch wiring — that is a technician’s job. Press OFF before you clear plants or debris from around the cabinet, and keep your hands away from the vents and the exhaust outlet, which get hot. If you smell gas, leave the area and call your gas utility or 911 from a safe place. Never run a generator indoors or near a garage, and keep a working carbon monoxide alarm in your home.

What this message means

Your Generac controller keeps track of two things. One is how many hours the engine has run. The other is how much calendar time has passed since the last service. When either number reaches a service point, the controller posts a maintenance reminder and turns on the yellow light. On current 10–28 kW units the yellow light flashes about once a second. Evolution manuals simply say it comes on when maintenance is required. Newer manuals call it the “Non-Critical Alert” light; older ones call it the “Maintenance” light.

A maintenance reminder is a warning, not an alarm. In Generac’s manuals, a warning needs attention but does not stop the generator. An alarm (red light) shuts the generator down to protect it. So your home is still protected during an outage. But the engine is now running on oil, a filter or spark plugs that are past their service point. That is not something to leave for long.

What each maintenance reminder includes

Message shownWhen it comes dueWhat the service includes
Service Schedule A
Reminder
Every 2 years or 200 run hours, whichever comes firstEngine oil and oil filter change, plus a battery check.
Service Schedule B
Reminder
Every 4 years or 400 run hours, whichever comes firstEverything in Schedule A, plus a new air filter and spark plug(s). On engines that require it, the valve clearance is inspected and adjusted.
Service C
Reminder
After the first 25 hours of run time on a new unitThe break-in service: an oil and oil filter change. On Evolution-era engines that need it, a valve-clearance check or adjustment as well. Current 10–28 kW units show it as “Service C” in the Mobile Link app.
Inspect Battery
Reminder
When the battery inspection comes due; on Evolution screens the Scheduled menu lists its next due pointA battery inspection and charge check. On Evolution 1.0 and 2.0 screens, the Battery menu shows the battery condition as Good, Inspect Battery or Check Battery. On current units, the app shows an Inspect Battery alert.

Some older Generac owner’s manuals (about 2013 to 2015) describe Schedule A as oil, oil filter and a tune-up. The 2-year / 200-hour and 4-year / 400-hour intervals are the same. Your owner’s manual has the exact list for your model.

Which Generac controllers show this reminder

  • Evolution 1.0 and 2.0 (units with a screen under the lid): the screen shows “Service Schedule A” or “Service Schedule B” as a warning message. The MAINT (or MAINTENANCE) menu includes Run Hrs, Scheduled and Maint Log. Run Hrs is the actual run hours. Scheduled shows when the next maintenance is due, as run hours and a date (for example “200 RnHr or 12/27/13”). Maint Log is the service history. Both versions also have a Battery menu item that shows the battery condition.
  • PowerZone 200 and current 10–28 kW units (no screen): the yellow status light flashes about once a second. The Mobile Link app shows “Service A”, “Service B”, “Service C” or “Inspect Battery”. The app is where the details live.
  • Nexus (older units): the screen shows a maintenance warning when a service period runs out. Generac’s 2010 manual calls for oil and filter every 200 hours or 2 years. The wording on the screen varies by model — check your owner’s manual.

Unlike most Generac alarms, the maintenance reminder has no four-digit E-code. Generac’s service manual lists it as a “Service Schedule” warning whose action step is simply “Perform Maintenance”.

Why it happens

  • Calendar time, not just run hours. Schedule A is due every two years even if the engine has barely run. Exercise runs add hours too. An exercise run is the short self-test the generator does on its own — usually once a week, though many newer models can be set to every two weeks or once a month. A few outages and normal aging of oil and battery add up too. This is the most common reason the reminder appears on a generator that “never runs”.
  • A long outage piled up the hours. Two hundred run hours is a little over eight days of continuous running. A multi-day storm outage can bring Schedule A due well before the two-year mark.
  • The unit is new. Generac’s manuals for current and Evolution-era units call for a break-in service after the first 25 hours of running. That is an oil and filter change and, on Evolution-era engines that need it, a valve-clearance check. Current 10–28 kW units prompt for it as Service C in the app. Evolution controllers prompt only for Schedule A and B, so the break-in service needs to be scheduled separately — check your owner’s manual. Generac’s 2010 manual for older Nexus units says those units need no break-in.
  • Our climate shortens the interval. Generac’s owner’s manuals say the oil and filter should be changed every year or 100 hours in cold weather (below 40 °F). The same applies to continuous hot-weather running (above 85 °F). A northern Illinois winter fits that description. That is why we recommend a yearly tune-up rather than waiting for the two-year reminder.
  • Several reminders stack up. Most Generac maintenance items run on two-year intervals, so several often come due together. The controller shows only one at a time. When the first is cleared, the next active one appears — another reminder, such as Inspect Battery, may show up next.
  • The last service was never logged. The reminder stays until it is cleared. If nobody cleared it at the control panel or in the app after the last oil change, it keeps showing. The maintenance log then has no record of the work.

What you can safely do

  1. Read the reminder. In the Mobile Link app, open the maintenance alert. On Evolution units the screen is under the lid: unlock and lift the lid only to read the screen and use its menu buttons. MAINT shows Run Hrs and Scheduled, and the Battery item shows the battery condition. Do not reach inside or remove any panel. A photo of the screen or the app helps us bring the right maintenance kit.
  2. Check for other messages. In the app, or on the Evolution screen while the lid is up, see whether Low Battery, Battery Problem, Charger Warning or Charger Missing AC is showing as well. If one is, mention it when you call.
  3. Look around the outside — no tools, no touching. Look for oil or fuel drips under the unit. Check whether sprinklers, downspouts, roof run-off or a sump-pump discharge is aimed at the cabinet. Leave the oil level to the technician; Generac’s manual notes the generator will shut down if the oil is low.
  4. Clear around it with the unit in OFF. If shrubs or tall grass have grown within about 3 feet of the louvers (the vent slots on the sides of the cabinet), or leaves and grass clippings have piled up against it, do this on a day when utility power is on and the generator is not running. Lift the lid and press OFF first. Trim and clear from the outside only, keep your hands away from the louvers and the exhaust outlet, and point any water source away from the cabinet. When you are done, press AUTO once and close the lid.
  5. Keep it in AUTO and book a tune-up — do not clear the reminder first. The reminder does not stop the generator from running, so leaving it in OFF would only leave your home without backup power. Pressing ENTER on an Evolution screen, or “Clear Maintenance” in the app, resets the maintenance counter. The controller also keeps a maintenance log with entries such as “Schedule A Serviced”. Clearing the reminder without doing the work hides a real need. If you cleared it by accident, just tell us when you call.

What a GSHA technician does at a Schedule A or B service

  • Makes the unit safe to work on, the way Generac’s manual describes preparing for maintenance. That means switching off the generator disconnect (the generator’s own main breaker, under the lid), pressing OFF, and removing the control fuse (the small fuse that powers the controller) before any panel comes off.
  • Checks the oil level on the dipstick, then changes the engine oil and oil filter with the oil grade Generac specifies for your model.
  • Inspects and tests the battery, checks that it is charging, and reads the controller’s battery condition on Evolution units (Good / Inspect Battery / Check Battery). Standby batteries are replaced when they no longer pass.
  • For Schedule B: replaces the air filter and the spark plug(s), checking plug gap against the spec for your engine. On engines that require it, inspects and adjusts the valve clearance. Generac excludes engines with hydraulic lifters, so not every model needs this step.
  • Does the yearly inspection items: enclosure louvers, fuel and oil lines and connections, water intrusion, and a fuel-system leak test. Where a sediment trap is fitted (a small fitting on the gas line that collects moisture and dirt), it is inspected and cleaned according to local codes.
  • Logs the service and clears the reminder. On Evolution units that is done at the control panel. On newer units it is done in the app or in Field Pro (Generac’s app for installers and technicians), which logs the service performed and resets the schedule. Then confirms the yellow light is off and the unit is back in AUTO with its exercise timer set.

When to call GSHA Services

  • Any Service Schedule A, Service Schedule B or Service C reminder is showing — that is the signal to schedule a tune-up.
  • The yellow light is on or flashing and you cannot see why (no screen, or the app is not set up).
  • The maintenance reminder is joined by Low Battery, Battery Problem, Charger Warning or Charger Missing AC. See our battery messages and charger messages guides.
  • It has been more than a year since the last service, reminder or not — Generac’s cold-weather interval is one year or 100 hours.
  • The reminder came back soon after a service. The work may not have been logged, or the unit may be racking up hours you were not expecting. We can read the run log and maintenance log to find out.

As an authorized Generac dealer, GSHA Services performs Schedule A and Schedule B maintenance with genuine Generac maintenance kits. We test and replace batteries and handle warranty repairs on qualifying units. Generac’s Evolution-era owner’s manuals say that emissions-critical maintenance — the air filter and spark plugs — must be done on schedule for the emissions warranty to stay valid. The current manual adds that maintenance records must be available on request for extended warranty coverage. So we log every visit. Learn more about our generator maintenance, generator repair and Generac generator installation services.

Request Generac service

Tell us which reminder is showing (Schedule A, B or C), your generator’s model and run hours if you have them, and the best time to reach you. Our team will contact you to schedule a maintenance visit. For an urgent problem during an outage, please call (224) 220-3660.

Generac service area

GSHA Services is based in Woodstock, IL and maintains Generac generators across Chicagoland, including McHenry County and Lake County, and southeastern Wisconsin. Not sure if we cover your address? Call us or send the form above.

Frequently asked questions

What does “Service Schedule A” mean on a Generac generator?

It means the controller has reached the Schedule A service point, which Generac sets at every 2 years or 200 run hours, whichever comes first. Schedule A is an engine oil and oil filter change plus a battery check. It is a maintenance reminder, not an alarm, so the generator still runs.

What is the difference between Generac Schedule A and Schedule B?

Schedule A (every 2 years or 200 hours) covers the oil, the oil filter and a battery check. Schedule B (every 4 years or 400 hours) includes everything in Schedule A plus a new air filter and spark plugs. It also includes a valve clearance check on engines that require it.

Will my Generac generator still run with a maintenance reminder showing?

Yes. A maintenance reminder is a yellow-light warning. In Generac’s manuals, a warning needs attention but does not stop the generator. Leave the unit in AUTO and schedule the service soon, so the engine is not running on overdue oil, filters or spark plugs.

How do I clear the Service Schedule A or B message on my Generac?

The reminder is meant to be cleared after the maintenance is done. On Evolution controllers with a screen it is cleared by pressing ENTER. On newer units it is cleared with Clear Maintenance in the Mobile Link app. Clearing it resets the maintenance counter, and the controller keeps a maintenance log with entries such as “Schedule A Serviced”. So let the technician clear it once the work is complete.

Why does my Generac say maintenance is due when it hardly ever runs?

Most Generac maintenance intervals are based on calendar time as well as run hours. Schedule A comes due every two years even with low hours, because oil and batteries age with time. In cold-weather areas like northern Illinois, Generac’s manual calls for an oil and filter change every year or 100 hours.

Generac® and Mobile Link® are trademarks of Generac Power Systems, Inc. GSHA Services, LTD is an authorized Generac dealer. This page is general guidance for homeowners; always follow the safety instructions in your owner’s manual and on the unit.